About andy_vvc2

andy_vvc2 · 06-25-2014

Hi all,We are trying to get an older Spirent Abacus 5000 call generator to connect to one of our 3845 router gateways.Initially we had tried to use MGCP with the backhaul to CallManager, but we were only able to get the port to be active at Layer1. ...

andy_vvc2 · 01-09-2014

Hi all,We have been asked to make an update to the 'Default Credential Policy' on CUCM 6.1. The update is easy enough to carry out: User Management > Credential Policy > Default Credential Policy.However, Cisco documentation isn't too clear as to wh...

andy_vvc2 · 02-22-2012

Hi all,We have lots of 7960 phones deployed which all work really well. We have Ext Mobility overlaid on these, and staff can happily logout and login where they like with no issues.We rolled some colour 7970 phones out a few years ago and found that...

andy_vvc2 · 11-30-2011

Hi all,We have three CUCM servers, 1x Pub and 2x Subs. Both subs are identified in the 'CMG' (CallManager Group). The DP for this site is linked to the CMG. All the site phones are in the DP.Within the CMG, how exactly does CUCM loadbalance the IP ...

andy_vvc2 · 02-16-2011

Hi all,We are lookng to deploy SNMPv3 trap management, to replace the SNMPv2 that we currently run on our Cisco IOS platforms.I *think* that we only need to add a few lines of new config, and will need to alter one existing "SNMP-server" line so the ...

Thanks George. She · 06-26-2014

Thanks George. Show controllers E1 did show some errors (slip errors). Once we set the clocking to be internal (i think) the errors stopped. E1 2/0 is up. Applique type is Channelized E1 - balanced Description: Call Generator No alarms detected. ...

andy_vvc2 · 01-16-2014

Quick bump. We've read a few links that suggest User and Application User passwords etc would be impacted. However, they don't mention the main Administrator account, nor if we would need to use Bulk Upload to change existing User and Application Us...

andy_vvc2 · 03-08-2012

Thanks Jonathan. We are conducting some more testing to see how limited the cross-device useage is with 'fixed' type profiles. We run over 1000 perfectly good 7960 IP phones so replacing them wont happen in one go. But obviously we cant buy them '...

andy_vvc2 · 02-23-2012

We have a mix of staff all using 7960 phones and 7960 Ext Mob acounts. Some have only 1 line. ther have up to 6 lines, some have a mix of lines and speed dials.I can create a 7962 button template of any type (lets say 6 lines) and assign that to th...

andy_vvc2 · 12-01-2011

Thanks Rob. Concise and quick response as always! Much appreciated!We have the disk-swop instructions from Cisco TAC so hopefully (if that goes smoothly out of hours) the re-register of the phones wont matter. Infact, it will be a good test of the ...

Member Since	‎11-06-2007 03:00 AM
Date Last Visited	‎08-18-2017 03:54 AM
Posts	132
Total Helpful Votes Received	10

User Statistics

User Activity

No ISDN L2 response from far end: "ISDN Se2/0:15 Q921: User TX -> SABMEp sapi=0 tei=0"

What impact do changes to the CUCM "Default Credential Policy" have?

Extension Mobility (7960 type) fully compatible with 7962 hardware?

CUCM 6.1 - how do CMG's balance IP phone requests?

Enabling SNMPv3 on IOS platforms

Thanks George. She

What impact do changes to the CUCM "Default Credential Policy" h

Re: Extension Mobility (7960 type) fully compatible with 7962 ha

Extension Mobility (7960 type) fully compatible with 7962 hardwa

CUCM 6.1 - how do CMG's balance IP phone requests?