About cleetusant

cleetusant · 12-29-2021

Hello,I wish to reset my 2911 router. Tried both method of sending Ctrl+Brk sequence as well as removing flash from the router. For both occasions, I am getting the below message and there is no prompt comes up.Readonly ROMMON initializedPASSWORD RE...

cleetusant · 03-27-2020

Hello As CAPWAP AP, the AP1701 gives maximum of 400 Mbps data rates to the clients. But when we set the AP1701 as Autonomous, it gives maximum of 144 Mbps only. How can I get 400 Mbps in Autonomous mode ? ThanksCleetus

cleetusant · 02-19-2020

Hello Geniuses, I have WLC 2504 and running with 1700 and 2700 series APs at the moment. Couple of AP 1130 also were working fine till few days ago. After a reboot of WLC due to the power failure, all of a sudden, all 1130 APs are not joining to the ...

cleetusant · 11-19-2019

Hello All,My WLC 2504 doesn't show the WLAN Profile name after restart the hardware; so none of the APs are able to join the WLC. The issue started with the version 8.0.140.0; so I tried to upgrade to version 8.0.152.0 and still the issue persists. ...

cleetusant · 06-16-2019

HelloMy Catalyst WS-3650-48TS switch shows read only flash file system.After IOS upgrade, switch went to rommon mode.While trying to boot from USB, it shows not enough memory for Full image.I tried to delete some files and make room for booting. Swit...

cleetusant · 08-28-2023

There is a very short interval after booting completes that will accept Ctrl+Brk. I got succeed by using Secure CRT by doing the same procedures.

cleetusant · 02-03-2023

Try the same as Rick said using 'Secure CRT' with same settings parameters. It worked for me.

cleetusant · 02-03-2023

Thank you Rick, Sorry for the late reply. The same thing I had tried and failed in Putty. But very later I tried "Secure CRT" and it worked well and I could recover password. Thank you for the lead.Cleetus

cleetusant · 01-03-2022

Dear Richard,Done all as you said. Waited around 6 minutes with 300 speed without anyinput. I got the same output as I mentioned earlier.After changing back to 9600(Didn't restart the router), I got the normalprompt only as mentioned below.*RTR-ACXB ...

cleetusant · 01-03-2022

Hi Richard,I set into 300 and waited 5 minutes by pressing Ctrl + Brk and I got theoutput below but no prompt. Am I missing anything more ?8▒̇▒)▒▒hL▒▒▒▒▒H9)▒▒▒}▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒w▒▒▒▒▒▒▒▒▒▒▒▒▒▒_▒▒▒▒▒▒▒_▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒...

Member Since	‎05-29-2015 09:50 PM
Date Last Visited	‎08-30-2023 12:33 AM
Posts	52
Total Helpful Votes Received	6

User Statistics

User Activity

Reset Cisco 2900 series

Wireless Data Rates

AP 1130 cannot Join to WLC - Certificate Error.

Cisco WLC 2504 issue after restart.

Catalyst 3650 Rommon flash Read only

Re: PASSWORD RECOVERY FUNCTIONALITY IS DISABLED

Re: PASSWORD RECOVERY FUNCTIONALITY IS DISABLED

Re: Have a look at this thread:

Re: PASSWORD RECOVERY FUNCTIONALITY IS DISABLED

Re: PASSWORD RECOVERY FUNCTIONALITY IS DISABLED