Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About sumitava123
Stats
Member since
03-06-2009
21
Posts
5
Helpful
1
Solution
09-20-2012
04:47 AM
Hello , I am not very familiar with the NM-8A/S module. There is a requrement to terminate a 2 MB link on 1 port of this module on a 2620 router. According to my limited knowladge about this interface it doesn't support more than 128 kb/s . Please clarify my doubt and if I can configure for 2 Mb can you please let me know how to do that as in any special kind of configuration is required or not. Thanks Sumit
... View more
Labels:
Created by
sumitava123
in Server Networking
in Server Networking
04-08-2011
04:50 AM
04-08-2011
04:50 AM
Hi , I am new to nexus and I am planning to configure source and destination based routing in nexus 7010. Can I configure it through QOS. Is there any kind of special license required for this. thnks sumit
... View more
Labels:
11-08-2010
08:46 PM
Hi , Can anyone please confirm me whether I can connect the nm-16-a module to any 2600/2500/1800 routers or not for configuring the terminal server. Someone told me that nm-16-a module is different for each router model and we need to connect model based nm-16-a module to the respective routers which I think is not right. Can anyone please confirm me this. Sumit
... View more
Labels:
11-01-2010
09:33 AM
Hi , I have 1 3745 router with 2 nm-4t card. I want to use it as a frame-realy switch for my home lab. Can you please let me know whether I can do that or not and if yes then how? I would also like to know the type of cable i need to connect to my router for wic-1-t and wic-2-t slot. Thanks Sumit
... View more
Labels:
10-05-2010
04:58 AM
Hi Can anyone please let me know how to configure w3c log from the command line of iron port s series and how to troubleshoot wccp from the command line. Thanks in advance. Sumit
... View more
Labels:
10-03-2010
11:27 PM
HI Estela , You can configure VSS on the core if u have 720-10g sup and MEC to ur 3550 switches. This increases the efficiency and availability to great extent. Sumit
... View more
09-27-2010
03:05 AM
Adding to what giuslar has informed I have also found that you have assigned IP address 10.10.126.53 on g0/0 but published network 10.10.126."54" 0.0.0.0(< Sumit
... View more
09-27-2010
02:50 AM
Hi Avilt , I can see that u have published x.x.88.0 network in area 0 in router a and in area 1 in router B.Thats why no neighborship is forming between them. Hope this helps . Cheers Sumit
... View more
09-24-2010
11:40 PM
Hi Naveen , Yes that is very much possible. You can configure different technologies to achieve load balancing but the best can be decided only after understanding your requirement and topology. Sumit
... View more
09-24-2010
08:17 AM
Hi , It is normally caused by some bug on the IOS . The only solution is to reload the switch. Then keep checking the process utilisation and keep a track of the processes which is continuously using most of the memory. Along with that open a TAC case aswell. Hope this helps Sumit
... View more
09-24-2010
02:10 AM
Hi Kukreja, When you try to ping the broadcast ip of a network you will get reply from all the host connected on that segment. Regrading the deny of that IP I am not sure what you are looking for. Regards Sumit
... View more
09-24-2010
02:07 AM
Hi , Can you please share the following command output. sh ip route | i null Regards Sumit
... View more
09-24-2010
01:16 AM
HI Andre , I am not able to understand your questions properly.The Null interface is typically used for preventing routing loops. Can you please elaborate your question. Sumit
... View more
09-20-2012
Hello ,I am not very familiar with the NM-8A/S module. There is a
requrement to terminate a 2 MB lin...
Created by
sumitava123
in Server Networking
04-08-2011
04-08-2011
Hi ,I am new to nexus and I am planning to configure source and
destination based routing in nexus 7...
11-08-2010
Hi ,Can anyone please confirm me whether I can connect the nm-16-a
module to any 2600/2500/1800 rout...
11-01-2010
Hi ,I have 1 3745 router with 2 nm-4t card. I want to use it as a
frame-realy switch for my home lab...
10-05-2010
Hi Can anyone please let me know how to configure w3c log from the
command line of iron port s serie...
10-03-2010
HI Estela ,You can configure VSS on the core if u have 720-10g sup and
MEC to ur 3550 switches. This...
09-27-2010
Adding to what giuslar has informed I have also found that you have
assigned IP address 10.10.126.53...
09-27-2010
Hi Avilt ,I can see that u have published x.x.88.0 network in area 0 in
router a and in area 1 in ro...
09-24-2010
Hi Naveen ,Yes that is very much possible. You can configure different
technologies to achieve load ...
Created by
sumitava123
in Switching
09-24-2010
09-24-2010
Hi ,It is normally caused by some bug on the IOS . The only solution is
to reload the switch. Then k...
09-24-2010
Hi Kukreja,When you try to ping the broadcast ip of a network you will
get reply from all the host c...
Public Statistics
| Date Registered | 03-06-2009 02:54 PM |
| Date Last Visited | 08-29-2018 12:01 AM |
| Total Messages Posted | 21 |
| Total Helpful Votes Received | 5 |
.jpg "Hall of Fame Master"){kind=icon}
