About kodanig

kodanig · 06-12-2007

I've used the 827 routers for ADSL ATM point to point circuits and now I'm having problems with a new 857 ADSL router when I try to configure EIGRP. IP routing is configured, I'm using IOS ver 12.4(11)T1 (C850-advsecurityk9-m)and when I try the CLI "...

kodanig · 09-26-2005

Hi, the root bridge of our Aironet 1310 bridge, S/W ver 12.3(4)JA, always seems to lose it's configuration for the "distance settings" when it reassociates with the non-root bridge. Current settings are set for 4 km but after it reassociates, the dis...

kodanig · 02-08-2005

Hi, I've upgraded 8 1310 bridges from 12.2(15)JA to 12.3(2)JA using the following CLI command: "archive download-sw /overwrte /reload tftp://xx.xx.xx.xx/c1310-k9w7-tar.123-2.JA2.tar". The upgrades seem to work fine, however, when I do a "show ver" an...

kodanig · 01-12-2005

Wireless newbie here. I was told not to ever provide the power source to a wireless bridge (350,1310 and 1410) until after an external antenna was installed on the bridge, prior to configuring the bridge. Simple enough to do on the 350 or 1310 but th...

kodanig · 06-24-2004

I've upgraded the firmware on a few 350 wireless bridges from 12.03 to 12.04 via the web interface using the image file "BR350v1204.img". After the reboot, the web interface shows the version 12.04 in the upper left corner of the web page. When I use...

kodanig · 06-14-2007

Hi Rick, surprised I missed that or surprised it's not available for this particular Cisco router? 8-) You are totally correct, although the configuration command is available in the IOS, it will not do EIGRP. Looks like I have to upgrade to the Ci...

kodanig · 02-14-2007

A good article for the gigabit stack gbic: http://www.cisco.com/en/US/customer/products/hw/modules/ps872/products_data_sheet09186a00800a1789.htmlBoth SFP and GBIC's are interface converters but different formats and are not interchangeable. The newer...

kodanig · 09-13-2005

Hi, you can go to the Data Sheet product overview http://www.cisco.com/en/US/customer/products/ps5861/products_data_sheet09186a00802252e1.html and take a look at Table 9 (Physical specs) under enclosure. NEMA4, IP56 etc are the specs listed. These s...

kodanig · 01-18-2005

Distance settings won't affect your signal strength. The setting adjusts the bridges time out values to account for the travel time required for the radio signals from bridge to bridge. Your settings should NOT be changed back to 0. Based on your fir...

kodanig · 06-28-2004

Hi, I did reset it to factory defaults, after the upgrade, but it had no effect. Since the web interface and the top of the home Summary Status page (in the command-line interface) are both showing 12.04, I'm pretty sure it's been upgraded but for so...

Member Since	‎06-24-2004 10:22 AM
Date Last Visited	‎01-10-2023 09:39 AM
Posts	10

User Statistics

User Activity

ADSL 857 Router problem with EIGRP

1310 Bridge loses distance settings

1310 bridge upgrade to 12.3(2)JA

1410 configuration

350 Wireless Bridge firmware

Re: ADSL 857 Router problem with EIGRP

Re: GBIC AND SFP

Re: 1300 Bridge ??

Re: Distance setting on 1410 Root Bridge

Re: 350 Wireless Bridge firmware