Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About rajat00700
08-18-2017
Stats
Member since
04-24-2012
11
Posts
0
Helpful
0
Solutions
05-12-2012
06:51 AM
Hi Guys, Thanks for your responses. I tried to configure the time based call routing as per Cisco documentation but no luck . I configure two time based route partition and asssociate them with a CSS that is already working but no luck.I applied it translation pattern also but no luck there also.Can you explain it with an senario so that i can find out where I went wrong. Thanks Rajat
... View more
Created by
rajat00700
in IP Telephony and Phones
in IP Telephony and Phones
05-12-2012
02:04 AM
05-12-2012
02:04 AM
Thanks--- Chris and Rob. I implemented it on the IP Phones There is no beep sound now.
... View more
Created by
rajat00700
in IP Telephony and Phones
in IP Telephony and Phones
05-08-2012
07:05 AM
05-08-2012
07:05 AM
Chris Its working fine when call is landing on the same line.But when the call is landing on another line of phone I am still getting the beep.
... View more
Created by
rajat00700
in IP Telephony and Phones
in IP Telephony and Phones
05-07-2012
09:30 PM
05-07-2012
09:30 PM
I have configured an call handler with supervise transfer.When the user is busy then call go to that handler and play the prompt and when caller is free it is landing on his desk that is working fine. But my issue is when call is redirected to user unsing supervise transfer and user don't pick it up it agian goes to handler but it never land back to the user extension.
... View more
Labels:
Created by
rajat00700
in IP Telephony and Phones
in IP Telephony and Phones
05-07-2012
05:44 AM
05-07-2012
05:44 AM
I have configured a hunt group with broadcast with the all user in the hunt group sharing the same 6 lines on there 7965 phones. When call came on the first line and the first user is busy on call another call come on the hunt it land on the second line at that time the fist person who is on call hear the beep sound and there is voice cracking at same time. There are two question : 1) Had anyone faces the same problem? 2) Can we restrict the beep sound when call came on second line?
... View more
Labels:
05-07-2012
12:13 AM
I have an senario with hunt group and Unity connection. I am using Unity connection 8.0 and UCS 8.5. The senario is like this in the office hours i want call to go to call handler after 5 rings or when the hunt group is busy that is working fine.But I want after office hours call should directly go to call handler without ringing on hunt.
... View more
- Tags:
- &
- 5
- 8
- after
- busy
- call
- connection_8.0
- go
- handler
- have
- hours
- hunt
- hunt_group
- like
- office
- rings
- the
- ucs
- unity
- unity_connection
- unity_connection_8.0
- working
Labels:
04-29-2012
10:51 PM
Hi Mink Thanks for yor reply.Its not working. My senario is like this I have an DID for incoming 4750XXXX when some call came in it translate last 4 digit and land to the internal extension 5489XXXX and it's working working fine with the dial peeer mentioned in the mail. But I want one specific number in DID to land on another internal number i.e when call came on 47504300 it should translate to 54894321 insted of 54894300 and rest all the numbers of DID range keep on translating in the same way.
... View more
04-29-2012
07:28 PM
Hi All, I have desgined an translation rule for in bound call its working fine voice translation-rule 1 rule 1 /^.*\(....\)/ /5489\1/ But I also want when some call some specific numbers in the same DID range whose last 4digts are like 4300 it should replaced with 54894241 insted of 54894300. I tried some transaltion rule that doen't work.
... View more
Labels:
04-25-2012
04:33 AM
I went to the market and checked . I found the connector. The connector used there is RJ48 but specifically designed for ISDN1500 standard cabling.
... View more
04-24-2012
08:11 PM
I am trying to rollout a site in Japan. I got struct while connecting the INS 1500 PRI from service provider(NTT) DSU.The jack used in NTT-ISDN DSU Look like RJ-45 but when we try to connect using RJ-45 connector we are unable to do so. Below is the photograph of Connector and female port. Did any face the same issue? Need help on what type of connector it is and wire positions in connector .
... View more
Labels:
05-12-2012
Hi Guys,Thanks for your responses.I tried to configure the time based
call routing as per Cisco docu...
Created by
rajat00700
in IP Telephony and Phones
05-12-2012
05-12-2012
Thanks--- Chris and Rob. I implemented it on the IP Phones There is no
beep sound now.
Created by
rajat00700
in IP Telephony and Phones
05-08-2012
05-08-2012
Chris Its working fine when call is landing on the same line.But when
the call is landing on another...
Created by
rajat00700
in IP Telephony and Phones
05-07-2012
05-07-2012
I have configured an call handler with supervise transfer.When the user
is busy then call go to that...
05-07-2012
I have configured a hunt group with broadcast with the all user in the
hunt group sharing the same 6...
05-07-2012
I have an senario with hunt group and Unity connection. I am using Unity
connection 8.0 and UCS 8.5....
04-29-2012
Hi MinkThanks for yor reply.Its not working.My senario is like this I
have an DID for incoming 4750X...
04-29-2012
Hi All,I have desgined an translation rule for in bound call its working
finevoice translation-rule ...
04-25-2012
I went to the market and checked . I found the connector. The connector
used there is RJ48 but speci...
Public Statistics
| Date Registered | 04-24-2012 07:57 PM |
| Date Last Visited | 08-18-2017 03:56 AM |
| Total Messages Posted | 11 |
