About Dmitry Podtikhov

Dmitry Podtikhov · 08-30-2013

Hi!I've got a license PAK L-AIR-CTVM-5-K9. So I believe I need to download the virtual WLC software, install it on ESX and load the license file. But I'm unable to download the .ova file from cisco support page because I've no valid service contract....

Dmitry Podtikhov · 07-02-2012

I need 3925 router and i want to install SM-ES3G-16-P etherswitch module with PoE into it. So my question is do I need PoE power supply or not? Will PoE ports on this module work with basic AC power supply?

Dmitry Podtikhov · 05-02-2012

Hi. I have a PBX connected to the Cisco 3825 router via one PRI line (I have one VWIC2-1MFT-T1/E1and one PVDM2-64 there) and there is a need to add another PRI link from the same PBX because one line is already not enough. This router acts as a VOIP ...

Dmitry Podtikhov · 02-01-2012

HiI've got a 3825 router running Cisco IOS 12.4(24)T connected to the pbx via PRI line. Hardware is VWIC2-1MFT-T1/E1 and PVDM2-64 onboard. This PRI line tends to be overloaded so we want to add another VWIC2-1MFT-T1/E1 card and PVDM2-64 resource to t...

Dmitry Podtikhov · 09-01-2011

Hi!Does anyone use ES2 enhanced etherswitch modules?Could not find out whether it functions identically as NM-16ESW or not. I do understand that ES3 module act like a separate device connected to the router chassis via internal interface and has its ...

Dmitry Podtikhov · 07-02-2012

Thank you for your reply. I've read the document, but it is still not clear to me though. Document says: "Power over Ethernet requires the PoE versions of the router power supplies". I have two PWR-3900-AC power supplies in the 3925 router (not PoE v...

Dmitry Podtikhov · 02-01-2012

I use G729a and my present DSP module can only handle 30 calls. I want to add another PVDM2-64 to increase the number of simultaneous calls to 60. (The DSP calculator suggest to add one PVDM2-48 + one PVDM2-8 though. This is unclear to me because for...

Dmitry Podtikhov · 02-01-2012

Thank you for your reply. Could not find any cisco doc with configuration example. As I can understand I'll need to1) Create global trunk grouptrunk-group PBX2) Assign interfaces to trunk group interface serial 0/0/0:15 trunk group PBX inte...

Dmitry Podtikhov · 09-13-2011

Thanks, Amit.I beleive it is hardware compatible with ISR G2s through the adapter. Btw, it is not available for ISR G2s in cisco configuration tool (though it was earlier)Found this link, it is declared EOS and EOL: http://www.cisco.com/en/US/prod/co...

Dmitry Podtikhov · 09-04-2011

Thank you for your reply.Do you use it in production environment? Currently we use older NM-16ESW and 38xx ISRs and it is rather convinient because they integrate with router chassis, share the same config and ports can be turned to routed mode. My u...

Member Since	‎11-18-2009 08:38 AM
Date Last Visited	‎08-18-2017 03:56 AM
Posts	44

User Statistics

User Activity

Virtual WLC software

Power supply requirement for SM-ES3G-16-P

Two PRI lines to different routers

Multiple PRI lines on 3825

ES2 etherswitch modules for ISR G2

Power supply requirement for SM-ES3G-16-P

Multiple PRI lines on 3825

Multiple PRI lines on 3825

ES2 etherswitch modules for ISR G2

ES2 etherswitch modules for ISR G2