About Craig Hunt

Craig Hunt · 01-20-2023

We have a 2 node ISE deployment that does Radius authentication for several WLCs and WLANs. I have the WLANs roughly configured so that half of them use ise01 then ise02 and the other half use ise02, ise01. However I am wondering if there is a dashbo...

Craig Hunt · 09-27-2020

I am looking for some help with intervlan routing on a WS-C3850-48P-E switch running SW version 03.07.05E.I have a few VLANs configured on the switch - 10-Data, 21-Wireless-Management, 105-VoIP.The switch acts as a DHCP server for the 21 and 105 vlan...

Craig Hunt · 04-17-2020

I am having an issue configuring SSH on a Catalyst 9300 switch. IOSXE 16.6.3.After generating the RSA, SSH gets enabled but I see "%SSH: Failed to encode IOS ASN.1 to SECSH format" in the output of 'show ip ssh'. I have tried regenerating the key mu...

Craig Hunt · 03-25-2020

I am hoping someone can help me with a new ISE 2.6 implementation. We have TACACS+ device management working very well but now we have been asked to give very limited switch CLI access to some helpdesk staff. Basically they should be able to do any...

Craig Hunt · 09-12-2019

We have an overhead paging system at a hospital that we are able to dial a 4-digit number to access. Everything works fine but we now have a request to not allow any external callers to access this DN. Only calls initiated internally should be able...

Craig Hunt · 11-06-2024

Also remember to make sure that a valid "Default 'From' email address:*" address in configured under Work Centers > Guest Access > Settings > Guest Email Settings.

Craig Hunt · 07-05-2024

The VTP Domain Name will be on line 00 starting in the 11th character. It carries over to the next line (01). In your case - NestleVNBH2The VTP password will be on line 50 starting at the 6th character. In your case - ntnvl00000000: BADB100D 00000...

Craig Hunt · 09-28-2020

BINGO!! Thanks Richard. That was it. I added a static route on the 2911 back to the 3850 and my PC now has access to everything. I guess I was incorrectly assuming that if there was a route from the PC > Switch > ISR, that it would automatically ...

Craig Hunt · 09-27-2020

uggggh. I think I jumped the gun. I can now access the 192.168.21.0/24 subnet while I am connected via vlan10 (192.168.10.0/24) but still can't get to the 192.168.105.0/24 subnet. Edit: I can actually ping all vlan interfaces hosted on the switch ...

Craig Hunt · 09-27-2020

Guys!! Thank you so much for your help. I can now access everything from the PC. I do believe it was my default gateway on my PC. I think I had it set to 192.168.10.1 (doesn't exist). Rookie mistake! I changed it to .2 and can now access the ot...

Member Since	‎11-22-2016 05:43 AM
Date Last Visited	‎11-18-2024 11:43 PM
Posts	37
Total Helpful Votes Received	15

User Statistics

User Activity

ISE Authentications Load Balance Graph

Looking for help with intervlan routing on 3850 switch

Catalyst 9300 - %SSH: Failed to encode IOS ASN.1 to SECSH format

Help with TACACS+ Command Sets in ISE 2.6

CUCM - Block all inbound external calls to certain DN

Re: Handy tip to easily test SMTP functionality in ISE

Re: Any way to recover / reset VTP password

Re: Looking for help with intervlan routing on 3850 switch

Re: Looking for help with intervlan routing on 3850 switch

Re: Looking for help with intervlan routing on 3850 switch