About Aaziz AMHAOUCH

Aaziz AMHAOUCH · 04-22-2016

Hello, Our customer bought two ASR 1001-X to run OTV between two Datacenters. The installed license is IPBASE and he bought ASR1K-DCI application part number. The issue is that we couldn't activate OTV feature on ASR 1001-X. Is there any procedure t...

Aaziz AMHAOUCH · 10-13-2015

Hi all,We need to upgrade an ASR9010 from 4.3.2 to 5.3.0 in order to install VSM cards. We did an upgrade in a test environment and we had the same problem as in this Cisco Bug: CSCuv20072 - Software upgrade causes reboot loop: https://tools.cisco.co...

Aaziz AMHAOUCH · 03-26-2015

Hi all,How can I implment QoS (Marking and Bandwidth reservation) over EoMPLS ? The customer is connected to PE (Cisco 7600 Series): NTU(Customer) --> Aggregation Switch (vlan) ---> PE (SVIs/Subinterface) Thank you in advance. Best Regards,Aaziz

Aaziz AMHAOUCH · 03-03-2015

Hi all,We have a problem in ASR 9000v Satellitte with CRS 5.1.3, it doesn't come UP :RP/0/RP0/CPU0:CRS#sh nv satellite status Tue Mar 3 11:54:14.305 UTCSatellite 200------------- Status: Discovery Stalled; Conflict: no Identification received yet ...

Aaziz AMHAOUCH · 02-24-2015

Hi All,I have a problem in CRS 8/S 400G: I have a 40X10GE-WLO Line Card on Slot 0 but it is not powered on and not shown in "show inventory" CLI command output. I tried to put this card in other slot but I had the same problemYou will find in attache...

Aaziz AMHAOUCH · 05-04-2016

Hi Manish, According to feature navigator OTV is supported using IP Base License : Best Regards, Aaziz

Aaziz AMHAOUCH · 05-03-2016

Hi Manish, Thank you for reply, where can I find this clearly in cisco documentation ? Best Regards, Aaziz

Aaziz AMHAOUCH · 10-16-2015

Hi Alexander,We used Turboboot 4.3.2 instead of 5.3.2 and it works: The node comes UP with 4.3.2 version and after that we tried again upgrade to 5.3.2 and this time it works !!- Is there a problem on Turboboot of 5.3.0 and 5.3.2 ?- Is it recommended...

Aaziz AMHAOUCH · 10-14-2015

Many Thanks for your quick feedback, usb device is recognized. Kindly refer to below logs:rommon 1 > dir usb: usb:\Directory of: usb:\ 10/13/15 05:11p10/13/15 05:11p <DIR> 4,096 ASR9K-iosxr-px-k9-5.3.0 10/13/15 05:11p10/13/15 05:11p <...

Aaziz AMHAOUCH · 10-14-2015

Hi Alexander, We have proceed with the steps thats you have decribes and failed to brings up the system. Kindly find bellow logs : rommon 2 > unset BOOTunset: "BOOT" does not existrommon 3 > TURBOBOOT=on,disk0,formatrommon 4 > syncrommon 5 > mediaboo...

Member Since	‎05-19-2012 04:13 AM
Date Last Visited	‎07-18-2018 12:03 AM
Posts	53

User Statistics

User Activity

Activate OTV feature on ASR 1001-X

Upgrade ASR9010 from 4.3.2 to 5.3.0

QoS over MPLS L2VPN (EoMPLS)

ASR 9000v sat fails to come up CRS 5.1.3

40X10GE-WLO not shown/powered on CRS-8/S-B-400G

Hi Manish,

Hi Manish,

Hi Alexander,We used

Many Thanks for your quick

Hi Alexander, We have proceed