About cisco.anubhav

cisco.anubhav · 01-02-2013

hi,We in our network had conventional circuits ,we have stm-1 installed at 7200 router which supports 63 e1 channels,we are using 5 e1 channels for 5 locations,all these were conventional copper links where g.703 and v.35 modems were used.Recently th...

cisco.anubhav · 12-19-2012

Hi,I have ben using following AAA commands and getting my routersauthenticated from TACS server SE 4.2.Now i need to get cisco 3560 and 6513 switches authenticated by the same ACS server,kindly suggest if any changes may be required in the commands.a...

cisco.anubhav · 11-23-2012

hi,can we use ranges cut out from a single subnet i.e.;(10.220.6.0/28 and 10.220.6.16/28) on diffrnent vlans say vlan 14 and 15 respectivly.thanks.

cisco.anubhav · 10-26-2012

hi,i have a trinagle network B and C are connected to A ,a has static default route to isp,while ospf is configured on all three ,b and c does not generate acandidate default routein theirrouting table.Here all links are 34 mb,i.e. A 34 /...

cisco.anubhav · 06-02-2012

Hi,I have a Cisco FWSM installed on Cisco 7613 router,the topology is like mentioned below, 7613+{FWSM}------3560---------3560----[10.220.0.0/29,10.220.1.0/29,10.220.2.0/29] Here we created a p2p link between 7613 gig port and switch3560 gig...

cisco.anubhav · 06-06-2012

Hi,thanks.What could be done in order to place fwsm in fromt of the router on a point to point link,should b end P2P ip which is on router serial inteface could be on fwsm outside interface ?thanks.

cisco.anubhav · 06-06-2012

Hi,i wanted to try the same on another FWSM,i removed old assignments and created new vlans 60-66 and assigned them to the FWSM ,but when i tried to given ip ads on router vlan interfaces i could give ip to both interfaces how ever i could not get th...

cisco.anubhav · 06-05-2012

hi,what if i put inside address to some range that is operational on 3560(e.g.:10.225.2.252/30 or 10.225.3),we cannot disturb our topology and we need that point to point link .Also there is one moe 3560 connected to the previously mentioned 3560Also...

cisco.anubhav · 06-04-2012

Hi,yes i dont have 192.168..x.x on my 3560 and yes original default gateway on 3560 is 10.225.62.145.I tried to change the default gateway of 7600 to divert all traffic to fwsm but OSPF that is running on all three 7600 core routers only is routing t...

cisco.anubhav · 06-04-2012

Hi,I removed outside route to see if the traffic that was coming from 3560 is still going through FWSM,because if i set default route to fwsm inside interface at 3560 ,traffic must come to fwsm and halt in the absence of outside route.I am trying to ...

Member Since	‎01-12-2010 05:32 AM
Date Last Visited	‎08-18-2017 03:56 AM
Posts	46

User Statistics

User Activity

Reg:Copper to ofc

Authentication for switches

same subnet ,diff vlans

OSPF default

Reg:FWSM router mode issue

Re: Reg:FWSM router mode issue

Re: Reg:FWSM router mode issue

Re: Reg:FWSM router mode issue

Re: Reg:FWSM router mode issue

Re: Reg:FWSM router mode issue