we had some switches mysteriously reloaded.  Upon investigation, TACACS+ Administration report show no user login to the device, no command was issued, and the reason = reload. how could this happen?       ... View more

Can I setup a user who may only be able to access from a specific IP address?  For example:  this user is only allowed access from 10.1.1.1, if source from anywhere else it would be denied. In User Setup\Client IP Address Assignment\ what is the meaning "Assign static IP address" and how is it used?  What is Network Access Restrictions (NAR) and how is it being used? Thanks. ... View more

I am unable to add ASR1002X routers to my inventory due to failure reason "device not supported".  Is this device type supported for LMS 3.2.1? RME ver 4.3.2 ... View more

can someone please tell me what is the equivalent command to configure on the Nexus 5596?  OS version 5.1(3)N2(1) Catalyst 45k ip igmp snooping vlan 1036 mrouter interface Po20 thank you ... View more

I am not able to run software or device update.  Initially I thought it was my proxy (Bluecoat) problem.  so I bypassed the proxy and still getting the same error.  based on the PSU.log, I am getting 404 error which ususally HTTP Not Found.  I am wondering if the URLs have been moved?  I've attached a sample of TCP stream in plain text. with proxy credential: [ Mon Mar 05 18:56:20 PST 2012 ] INFO   [SwUpdateAction : selectAllUpdates]  : Validated Cisco.com credentials.. [ Mon Mar 05 18:56:23 PST 2012 ] ERROR  [CcoDownloadAdapter : getXmlFileList]  : failed to connect to Cisco.com:RespCode=404, RespMsg=Not Found [ Mon Mar 05 18:56:23 PST 2012 ] ERROR  [RemoteRepSync : downloadPsuHeadersAsXml]  : VDSException thrown com.cisco.nm.xms.vds.VDSException: CcoDownloadAdapter::getfileList():failed to connect to Cisco.com. [ Mon Mar 05 18:56:23 PST 2012 ] INFO   [SwUpdateAction : selectAllUpdates]  : removing SwUpdateLock, due to exception.. bypass proxy: [ Tue Mar 06 14:57:24 PST 2012 ] INFO   [SecurityHandler : getCSProxyLogin]  : No proxy User Name configured [ Tue Mar 06 14:57:27 PST 2012 ] INFO   [SwUpdateAction : selectAllUpdates]  : Validated Cisco.com credentials.. [ Tue Mar 06 14:57:27 PST 2012 ] ERROR  [CcoDownloadAdapter : getXmlFileList]  : failed to connect to Cisco.com:RespCode=404, RespMsg=Not Found [ Tue Mar 06 14:57:27 PST 2012 ] ERROR  [RemoteRepSync : downloadPsuHeadersAsXml]  : VDSException thrown com.cisco.nm.xms.vds.VDSException: CcoDownloadAdapter::getfileList():failed to connect to Cisco.com. [ Tue Mar 06 14:57:27 PST 2012 ] INFO   [SwUpdateAction : selectAllUpdates]  : removing SwUpdateLock, due to exception.. ... View more

based on my research it seems that in order to have a successful deployment of WOL I would need minimal of the following. 1. the L3 device where the server is attached, enable ip forward-protocol. 2. the L3 interface where the server is connected needs ip helper-address.  this helper address should be the broadcast address of the client PC network. 3. the L3 interface where the client PC is connected needs ip directed-broadcast. my question regarding item #2.  what happen if I have hundreds of client networks span across the private WAN.  do I need to configure each and everyone of their network broadcast address as ip helper-address?  if not, what are my alternatives? thanks in advance ... View more

Can someone please explain what this syslog message means?  Being getting this on my 3945e series routers.  My gut tells me they are caused by our Security guys scanning my routers with invalid login attempts. %SSH-3-DH_RANGE_FAIL: Client DH key range mismatch with maximum configured DH key on server ... View more

I would like to use a different port to source syslog messages.  Can I specify an alternative port other than default? on IOS I think the command is "logging host x.x.x.x transport udp port xxx". ... View more