In this case I would set up another CSS (which will be set on the lines for the devices 29xx) that contains an additional Partition (perhaps called Reroute_2525) which gets the translation pattern assigned. ... View more

The pattern should be: 2222. Discard digits: PreDot Prefix outgoing calls: 2525 You can apply it to the appropiate Partition / CSS ... View more

Hi David, the Port is configured as a Accesspoint Smartport, with native vlan data. I also tried to use voice vlan as native vlan, but I got the following error message: "Vlan voice can not be associated with a SSID on wireless controller(s), if connected to the port(s)." I even tried to set the configuration via cli to trunk mode, but it didn´t help either. Do you have another idea (eg. multicast configuration)? Thanks. Stefan ... View more

Hi Paolo, the MOH works fine on the internal AP. I connected the 1131 to an  ethernet port. While the phone is connected to the external AP the MOH  doesn´t work. See my post to David. Perhaps you have an idea regarding multicast configuration. Bye Stefan ... View more

Hi David, the MOH works fine on the internal AP. I connected the 1131 to an ethernet port. While the phone is connected to the external AP the MOH doesn´t work. I have another Problem, which also seems to handle with multicast. I have some devices which connect through UPnP, which is also not working on the external AP. So my question would now be...how do I configure multicast correctly? Bye Stefan ... View more

Hi Paolo, the devices are in the same VLAN. But it doesn´t work. Any further ideas? Thanks Stefan ... View more

Hi David, hi Christian thank you for your help, the DSP Ressources are up now: UC_540#sh dsp all Dspfarm Profile Configuration Profile ID = 3, Service = TRANSCODING, Resource ID = 1 Profile Description : Profile Service Mode : Non Secure Profile Admin State : UP Profile Operation State : ACTIVE IN PROGRESS Application : SCCP   Status : ASSOCIATION IN PROGRESS Resource Provider : FLEX_DSPRM   Status : UP Number of Resource Configured : 2 Number of Resource Available : 2 Codec Configuration Codec : g711ulaw, Maximum Packetization Period : 30 Codec : g711alaw, Maximum Packetization Period : 30 Codec : g729ar8, Maximum Packetization Period : 60 Codec : g729abr8, Maximum Packetization Period : 60 Codec : g729r8, Maximum Packetization Period : 60 Codec : g729br8, Maximum Packetization Period : 60 Dspfarm Profile Configuration Profile ID = 1, Service = CONFERENCING, Resource ID = 2 Profile Description : DO NOT MODIFY, active CCA conference profile - CCA2.0 codec711 Profile Service Mode : Non Secure Profile Admin State : UP Profile Operation State : ACTIVE Application : SCCP   Status : ASSOCIATED Resource Provider : FLEX_DSPRM   Status : UP Number of Resource Configured : 2 Number of Resource Available : 2 Codec Configuration Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required SLOT DSP VERSION  STATUS CHNL USE   TYPE    RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED 0    1   26.8.3   UP     N/A  FREE  xcode  1      -         -         - 0    2   26.8.3   UP     N/A  FREE  xcode  1      -         -         - 0    4   26.8.3   UP     N/A  FREE  conf   2      -         -         - 0    4   26.8.3   UP     N/A  FREE  conf   2      -         -         - Total number of DSPFARM DSP channel(s) 4 --------- But it´s still notworking. At the moment I have only one analog phone and an IP-Phone connected. When I press the flash button on the analog phone the MOH can be heard on the IP-Phone. When I press Hold on the IP-Phone, I only hear a short double beep on the analog phone. What else do I have to do? Bye Stefan ... View more

Hi Alex, yes, I´m using German localization pack. I made a test by editing the menu objects in different modes. I added options step by step, when I e.g add mobility in idle, all options disappear in idle mode. Which problem can cause this? Bye Stefan ... View more