Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About learnerkang
Stats
Member since
10-26-2007
44
Posts
0
Helpful
0
Solutions
12-31-2008
03:17 PM
Yes, you are right. That is recursive route. SWITCH1#show ip route 10.210.2.2 Routing entry for 10.210.2.2/32 Known via "eigrp 100", distance 90, metric 130816, type internal Redistributing via eigrp 100 Last update from 10.10.52.2 on Vlan752, 1d00h ago Routing Descriptor Blocks: 10.10.52.2, from 10.10.52.2, 1d00h ago, via Vlan752 Route metric is 130816, traffic share count is 1 Total delay is 5010 microseconds, minimum bandwidth is 1000000 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 1 10.10.28.2, from 10.10.28.2, 1d00h ago, via Vlan728 Route metric is 130816, traffic share count is 1 Total delay is 5010 microseconds, minimum bandwidth is 1000000 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 1 10.10.25.2, from 10.10.25.2, 1d00h ago, via Vlan725 Route metric is 130816, traffic share count is 1 Total delay is 5010 microseconds, minimum bandwidth is 1000000 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 1 * 10.10.23.2, from 10.10.23.2, 1d00h ago, via Vlan723 Route metric is 130816, traffic share count is 1 Total delay is 5010 microseconds, minimum bandwidth is 1000000 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 1 Thanks for all your help!
... View more
12-31-2008
11:12 AM
Can anyone tell me why I got differenct routing path for same destination 10.10.169.136? SWITCH1#show ip route 10.10.169.136 Routing entry for 10.10.169.0/24 Known via "static", distance 1, metric 0 Redistributing via eigrp 100 Advertised by eigrp 100 Routing Descriptor Blocks: * 10.210.2.2 Route metric is 0, traffic share count is 1 So the next hop should be 10.210.2.2(static route), right? But when I trace the same destionation, the first hop I got is not 10.210.2.2. Please refer the following - SWITCH1#trace 10.10.169.136 Type escape sequence to abort. Tracing the route to 10.10.169.136 1 10.10.52.2 0 msec 10.10.23.2 0 msec 10.10.25.2 0 msec 2 10.252.1.170 4 msec 0 msec 0 msec 3 10.252.1.174 4 msec 0 msec 0 msec 4 10.10.169.136 0 msec * 0 msec Can anyone explian it to me? Thanks in advance.
... View more
Labels:
Created by
learnerkang
in IP Telephony and Phones
in IP Telephony and Phones
09-07-2008
08:30 AM
09-07-2008
08:30 AM
I'll do that. Thanks.
... View more
Created by
learnerkang
in IP Telephony and Phones
in IP Telephony and Phones
09-07-2008
08:29 AM
09-07-2008
08:29 AM
Thanks for you info.
... View more
Created by
learnerkang
in IP Telephony and Phones
in IP Telephony and Phones
09-06-2008
09:25 AM
09-06-2008
09:25 AM
We have H323 GW. Sorry I'm new to VOIP world. could you pls give me detailed info about how to dial the number from the gateway? Thanks.
... View more
Created by
learnerkang
in IP Telephony and Phones
in IP Telephony and Phones
09-06-2008
07:10 AM
09-06-2008
07:10 AM
Thanks a lot for reply. The one thing confused me is: how to tell this output is for incoming call or for outgoing call? Because I dialed 95597451 from one of the internal number '5065597720' while testing.
... View more
Created by
learnerkang
in IP Telephony and Phones
in IP Telephony and Phones
09-05-2008
03:11 PM
09-05-2008
03:11 PM
This user (only one) can't receive calls from outside of my company. Callers get busy tone after dialing his number. But he is able to dial out and recieve calls from internal. Here is output of "Debug isdn q931" Sep 5 14:17:44.370 PST: ISDN Se1/0:23 Q931: RX <- CONNECT pd = 8 callref = 0xFA46 Sep 5 14:17:44.374 PST: ISDN Se1/0:23 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x7A46 Sep 5 14:17:47.470 PST: ISDN Se1/0:23 Q931: pak_private_number: Invalid type/plan 0x0 0x0 may be overriden; sw-type 13 Sep 5 14:17:47.470 PST: ISDN Se1/0:23 Q931: pak_private_number: Invalid type/plan 0x0 0x0 may be overriden; sw-type 13 Sep 5 14:17:47.470 PST: ISDN Se1/0:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x1, Called num 5597451 Sep 5 14:17:47.470 PST: ISDN Se1/0:23 Q931: TX -> SETUP pd = 8 callref = 0x7A48 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98396 Exclusive, Channel 22 Calling Party Number i = 0x0181, '5065597720' Plan:ISDN, Type:Unknown Called Party Number i = 0x81, '5597451' Plan:ISDN, Type:Unknown Sep 5 14:17:47.706 PST: ISDN Se1/0:23 Q931: RX <- CALL_PROC pd = 8 callref = 0xFA48 Channel ID i = 0xA98396 Exclusive, Channel 22 Sep 5 14:17:48.130 PST: ISDN Se1/0:23 Q931: RX <- PROGRESS pd = 8 callref = 0xFA48 Progress Ind i = 0x8288 - In-band info or appropriate now available Called number 5597451 is having incoming calls problem. Any suggestion will be appreciated!
... View more
Labels:
08-28-2008
01:18 PM
Here is output for debug isdn q931: Aug 27 15:44:33.592 PST: ISDN Se1/0:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x1, Calling num 613XXXXXXX Aug 27 15:44:33.596 PST: ISDN Se1/0:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x1, Called num 15094558770 Aug 27 15:44:33.596 PST: ISDN Se1/0:23 Q931: TX -> SETUP pd = 8 callref = 0x44C4 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98389 Exclusive, Channel 9 Calling Party Number i = 0x0181, '613XXXXXXX' Plan:ISDN, Type:Unknown Called Party Number i = 0x81, '15094558770' Plan:ISDN, Type:Unknown Aug 27 15:44:33.680 PST: ISDN Se1/0:23 Q931: RX <- CALL_PROC pd = 8 callref = 0xC4C4 Channel ID i = 0xA98389 Exclusive, Channel 9 Aug 27 15:44:33.680 PST: ISDN Se1/0:23 Q931: RX <- PROGRESS pd = 8 callref = 0xC4C4 Cause i = 0x8081 - Unallocated/unassigned number
... View more
08-28-2008
01:14 PM
We tried 509 number on two extensions and got same problem. Users got "we can't complete the call with number you've dialed" after 3 rings. CSS looks Okay. We are checking the Router Pattern now. By the way, it should be nothing to do with Translation pattern, right?
... View more
08-28-2008
12:38 PM
one of our remote sites can't dial valid 509 number which worked on other sites. Debug isdn q931 and we got: Cause i = 0x8081 - Unallocated/unassigned number Any idear what's going on? Thanks.
... View more
Labels:
Created by
learnerkang
in VPN and AnyConnect
in VPN and AnyConnect
08-27-2008
11:58 AM
08-27-2008
11:58 AM
This is what I need. Thanks
... View more
Created by
learnerkang
in VPN and AnyConnect
in VPN and AnyConnect
08-27-2008
11:42 AM
08-27-2008
11:42 AM
I telnet to one of the switches and issue "debug isdn q931". but I didn't get anything coming up. I'm not sure which command to turn on it. Can anyone help me out? Thanks
... View more
Labels:
08-27-2008
09:03 AM
There is a fax machine that stopped working suddenly. We have verified the configuration on CCM and Gateway(VG224). When people dial the number, it rings and no answer. We tried other lines on this Gateway and work. Any idea about it? We also tried debug isdn Q931 and checked dial-peer, we didn't find anything wrong.
... View more
Labels:
12-31-2008
Yes, you are right. That is recursive route. SWITCH1#show ip route
10.210.2.2 Routing entry for 10.2...
12-31-2008
Can anyone tell me why I got differenct routing path for same
destination 10.10.169.136?SWITCH1#show...
Created by
learnerkang
in Unified Communications Infrastructure
09-22-2008
09-22-2008
When user check the VM she's getting the error message "Your inbox is
almost full. If your inbox exc...
Created by
learnerkang
in IP Telephony and Phones
09-06-2008
09-06-2008
We have H323 GW. Sorry I'm new to VOIP world. could you pls give me
detailed info about how to dial ...
Created by
learnerkang
in IP Telephony and Phones
09-06-2008
09-06-2008
Thanks a lot for reply. The one thing confused me is:how to tell this
output is for incoming call or...
Created by
learnerkang
in IP Telephony and Phones
09-05-2008
09-05-2008
This user (only one) can't receive calls from outside of my company.
Callers get busy tone after dia...
08-28-2008
Here is output for debug isdn q931:Aug 27 15:44:33.592 PST: ISDN
Se1/0:23 Q931: Applying typeplan fo...
08-28-2008
We tried 509 number on two extensions and got same problem. Users got
"we can't complete the call wi...
08-28-2008
one of our remote sites can't dial valid 509 number which worked on
other sites.Debug isdn q931 and ...
08-27-2008
I telnet to one of the switches and issue "debug isdn q931". but I
didn't get anything coming up. I'...
Public Statistics
| Date Registered | 10-26-2007 03:40 AM |
| Date Last Visited | 08-18-2017 03:56 AM |
| Total Messages Posted | 44 |
Helpful Votes Given To
.jpg "Hall of Fame Cisco Employee"){kind=icon}
