About ondjultomte

ondjultomte · 12-10-2018

I have two 5520 that currently only has one PSU installed , but the cli shows that the second PSU is present but not powered. Power Supply 1................................... Present, OKPower Supply 2................................... Present, Of...

ondjultomte · 09-14-2018

Im using check_nwc_health and hardware-health check on a 6807a and I get a alarm for The check reports: fan 103 (chassis-1 Power Supply 2 Fan) is notFunctioning Switch shows: sh environment status switch 1 power-supply 2switch 1 power-supply 2: s...

ondjultomte · 06-27-2018

I got a WS-C3650-48PS 03.07.05.E in BUNDLE mode that I tried to upgrade. I tried to just add the standard boot system flash:image.bin and switch to INSTALL mode with the packages.conf as boot file. The problem is that each boot system comma...

ondjultomte · 06-07-2018

Hi! We are SNMP monitoring cacheTotalRespTimeNow and from time to time this value peaks extremely high, but no users has complain We have added the accesslogs Date: %L Dst-IP: %k UsrAgnt: %u ADGroup: %g AuthMethod: %m TransID: %I PrfPara: %:<a ...

ondjultomte · 05-29-2018

(Cisco Controller) >show bootPrimary Boot Image............................... 8.3.133.0 (active)Backup Boot Image................................ 8.2.151.0 (default) (Cisco Controller-Standby) >show bootPrimary Boot Image.............................

ondjultomte · 10-22-2018

Thanx ! I will set the CM to 10.5. Its a bit worrying tho, in the compatibility matrix there is no match for that combination

ondjultomte · 10-19-2018

I have the same problem. How can you choose CM version between 9.1 and 10.5 ? I need 10.0. We are using SMA 10.1.0-052 and WSA 10.1.1-235 and currently CM 9.1

ondjultomte · 07-10-2018

1531102150.668 240068 10..xx.xx.xx TCP_MISS/200 950 TCP_CONNECT 216.58.209.138:443 - DIRECT/safebrowsing.googleapis.com - PASSTHRU_CUSTOMCAT_7-NoAuthPolicy-NoAuthId-NONE-NONE-NONE-DefaultGroup <C_NoAu,1.5,-,"-",-,-,-,-,"-",-,-,-,"-",-,-,"-","-",-,-,I...

ondjultomte · 07-05-2018

Hi ! Now I did some more testing. First I tried: no boot system end wr no difference , then I tried no boot system flash:thefiletoberemoved end wr no difference. But Right now I tried it again and it worked rou1#show boot ------------------...

ondjultomte · 06-27-2018

Hi, never thought of that :) Switch 1---------------------------Current Boot Variables:BOOT variable = flash:packages.conf;flash:cat3k_caa-universalk9.16.03.06.SPA.bin;flash:cat3k_caa-universalk9.SPA.03.07.05.E.152-3.E5.bin; Boot Variables on next...

Member Since	‎08-04-2017 02:25 PM
Date Last Visited	‎05-08-2019 12:01 AM
Posts	30

User Statistics

User Activity

5520 show psu2 present but its not

6807 check_nwc_health fan 103 (chassis-1 Power Supply 2 Fan) is notFunctioning

Can't update 3650 from 3.7.5

High cacheTotalRespTimeNow value but no indication of problem

Default image mismatch between active and standby WLC

Re: Which WSA config master do I use in SMA for version 10.1.1?

Re: Which WSA config master do I use in SMA for version 10.1.1?

Re: High cacheTotalRespTimeNow value but no indication of problem

Re: Can't update 3650 from 3.7.5

Re: Can't update 3650 from 3.7.5