I have added my MESH AP's to the map and the MESH links appear on the map as 0 SNR.  I can run the link test Parent-> Child and vise-versa and SNR os good.  If I go to Monitor->Access Points-><AP Name>-> Link detail, everything is zeroed out.  I do have "Refresh from Network" enabled.  Am I missing a configuration parameter somewhere? ... View more

I have configured PI 1.3 to monitor all my switches and routers in the network.  On the HOME page under Detailed Dashboards, I have Dashlets for "Top N Clients (In & Out)" as well as "Number of Wired and Wirless Clients"  On both graphs, an overwhelming majority of cients show up as "Unknown".  I can view a particular Top N Client's IP address  in OPERATE>Clients and Users  under the "TYPE" field they show up as Wired.  Why wouldn't this info show up in the Dashlet as wired?   I do haveother sites that do show Wired and Wireless users correctly.  What am I missing?? ... View more

I'm in the process of migrating from WCS on Linux versio 7.0.164.3 to NCS.  Trying to follow the Release Notes for NCS 1.0 for exporting the date from WCS.  Per the doc's, I stop WCS, and run the export script. I get a screen full of data that scrolls by.  I then run the export.sh all /data/wcs.zip command and I get a "command not found".  I'm not a Linux person so I'm not sure what I am doing wrong.  Do I need to be in a certain directory to run the command? If so, which directory?  Any ideas what I could be doing wrong? ... View more

I have an existing pair of bridges operating at Layer 2 and would like to add a second pair of bridges for redundancy/bandwidth.  I'm finding mixed documentation as to whether a pair of bridges operating as a layer 2 Etherchannel is a CIsco supported configuration. Is there a design document that shows Layer 2 Etherchannel with wireless bridges? ... View more

I am trying to get a Nortel phone to authenticate using 802.1x and MDA. The phone will authenticate fine when using multi-host mode. When I change to MDA, the phone says "EAP Not Authenticated" however the ACS server see's a passed authentication and showing the dot1x switchport interface detail command, I see the Voice domain authenticated and I see spanning-tree forwarding for the Voice Vlan on that port. The phone gets to the DHCP request and stops there. It appears that it falls back to the guest-vlan and gets an IP address from there. I have the required Cisco attribute configured in ACS. Has anyone else experienced this problem or have any ideas what could be wrong? ... View more

I have a need to use 1 CSS to balance server farms that reside on 2 different PIX segments. So Internet traffic destined for a server farm on "DMZ 1" would be balanced and traffic destined for a server farm on "DMZ 2" would be balanced through the same CSS. Also, I have a 2nd CSS for redundancy. I am not sure of the best way to accomplish this and keep traffic routing through the proper PIX interface. ... View more

I have a WiSM module installed in my 6500 managed by WCS. Iwant to get Lobby Ambassader working but I do not see where I can do that with WCS. Do I have to create a Lobby Ambassader on each controller and then create a username/password on each controller for guest access? It does not seem that the controllers share this information. ... View more

I am trying to set up a single 7200 with a DS3 to one ISP and a T1 to a second ISP for failover. I have a static default route to the DS3 and a second static route with a higher admin distance to the T1. The router detects the DS3 outage fine and will route out to the T1. The problem is getting the proper NAT IP addresses. I am using NAT w/route-maps howeer I am not clear how to set the route-map to have packets from the same source and destination change NAT pools based upon the next hop interface. Is what I am trying to do possible? My config looks like this: interface FastEthernet0/0 description Connection to Firewall ip address 172.20.1.17 255.255.255.248 ip nat inside duplex full speed 100 ! interface Serial1/0 description DS-3 to ISP1 ip address 10.1.1.2 255.255.255.252 ip nat outside dsu bandwidth 44210 framing c-bit cablelength 10 serial restart-delay 0 ! interface Serial2/0:0 description 3MB to ISP2 ip address 10.2.2.2 255.255.255.252 ip nat outside encapsulation ppp fair-queue ! interface Serial2/1:0 description 3MB to ISP2 ip address 10.3.3.2 255.255.255.252 ip nat outside encapsulation ppp fair-queue ! ip nat pool ISP2 10.200.200.33 10.200.200.62 netmask 255.255.255.224 ip nat pool ISP1 10.100.100.33 10.100.100.62 netmask 255.255.255.224 ip nat inside source route-map ISP1 pool ISP1 overload ip nat inside source route-map ISP2 pool ISP2 overload ip classless ip route 0.0.0.0 0.0.0.0 Serial1/0 10.1.1.1 ip route 0.0.0.0 0.0.0.0 Serial2/0:0 10.2.2.1 200 ip route 0.0.0.0 0.0.0.0 Serial2/1:0 10.3.3.1 200 ! access-list 1 permit 172.20.0.0 access-list 10 permit 10.2.2.1 access-list 11 permit 10.3.3.1 access-list 15 permit 10.1.1.1 access-list 101 permit ip 172.20.0.0 0.0.255.255 any ! route-map ISP2 permit 10 match ip address 101 match ip next-hop 10 ! ! route-map ISP1 permit 10 match ip address 101 match ip next-hop 15 ... View more