Hi; To configure the static route on ASA please find the command below: route outside 0.0.0.0 0.0.0.0 192.168.1.1 Note: outside is the name of Cisco ASA firewall (Eth 0/0) which is connected to cable modem. To configure the name on interface is below: interface Ethernet0/0 nameif outside security-level 0 ip address 192.168.1.5 255.255.255.0 Thanks & Best regards; ... View more

Hi; 1) To disable the Telnet on Nexus 7000, is just need to disable the telnet feature: no feature telnet 2) To remove the  Switchport access vlan4 is simple as we are removing on normal Cisco switch & there will be issue: interface port-channel5  no switchport access vlan 4 Thanks & Best regards; ... View more

Yes. ... View more

Hi; Can you share the model of switches which you are using on your network? Idealy all the SVI should be either create on Core Switch (if you have L3 supported switch) or configure on Router. In the output you shared which shows your client have SVI, which is not recommended solution.  Thanks & Best regards; ... View more

Hi; It's always recommend to use L3 connectivity b/w 2 sites instead of using L2 to avoid STP loops. If it required to extand Vlan from b/w 2 sites then you need to be careful with reference to STP: 1. Site A switch should be STP root. 2. Trunk allowed vlan should be used to restrict the specific vlan to traverse b/w 2 sites. 3. Always configure Strom control to restrict the broadcast on L2 wan link. Thanks & Best regards; ... View more

Hi; I am doubtful & it will not work what you are looking for. I never work on twinex/DAC-cable and never see the design what you are looking for. On other side how you distinguish the traffic coming from ASR & 3850 on  Nexus side. Thanks & Best regards; ... View more

Hi; If you are using GLC-T then you can use CAT-5e or CAT-6 Cable. And if you are using GLC-SX-MMD then you can use LC-LC fiber patch cord. Thanks & Best regards; ... View more

Hi; To connect  these to switches you need either GLC-T(1G UTP) or GLC-SX-MM(1G Fiber) on Nexus 3524 switch. We  Thanks & Best regards; ... View more

Hi Waqas; With the help of vPC we can create a multi-chassis etherchannel. If you have same device (ports on same FEX/Nexus switches) we don't required vPC, port will configured as simple port-channel. int eth101/1/1 channel-group 10 mode active int eth101/1/2 channel-group 10 mode active int port-channel 10 no shut switchport mode access/trunk If your Server/Network devices connected to 2 FEX/Nexus switches and want to configure multi-chassis etherchannel then you need to configure port-channel with vPC. int eth101/1/1 channel-group 5 mode active int eth102/1/1 channel-group 5 mode active int port-channel 5 no shut switchport mode access/trunk vpc 5 Thanks & Best regards; ... View more

Hi; Just want to understand your server have 2 connection with each Nexus 5K or 1 connection with each N5K. If it's one connection to each Nexus 5K, and you do not want you use vPC means no need to configure the port-channel on Nexus 5K also and your server configure as active/passive interface. If your Server have 2 connection with each Nexus 5K and you want to configure 2 separate port-channel with each Nexus 5K you can do it, even you can use same port-channel no.(Po203) due to port-channel no. is locally significance. Just need to configure port-channel without vPC. Here my suggestion is whenever you have Server with multiple link you should configure port-channel no nexus environment & in Nexus configure port-channel with vPC which will provide you redundancy and provide double of bandwidth via load sharing on multiply links. Thanks & Best regards; ... View more

Hi; To configure the port-channel / etherchannel the speed, duplex setting should be same. unequal speed/link can not create port-channel. 2nd if you don't want spread the broadcast domain you have option via creating L3 link b/w 2 switches. Thanks & best regards; ... View more

Hi; It's depend on your network requirement. You can also run HSRP b/w VSS1 & VSS2 and you can also enable L3 routing between VSS1 & VSS2. Note: As you opened case with reference to FHRP, FHRP is required when you are running OTV b/w 2 sites running on Nexus. Thanks & Best regards; ... View more