About Justin Hale

Justin Hale · 06-17-2020

Hi All, I have an issue that just presented itself out of no-where. I'm using DOT1x and have Cisco IP Phones. I'm using C2960-X-FPD-L switches. I have run the following port config for years. interface GigabitEthernet1/0/37description Standard Compu...

Justin Hale · 06-03-2015

HI All, I have a CCM 10.5.2 system in the USA. Our policy is that 911 needs route to Emergency services. we use 9 for our outside line. 9.911 is not acceptable, and urgent Priority must be used. we cannot delay these calls in any manner e.g "911?" .c...

Justin Hale · 08-17-2014

HI All,Im building a new CUCM10.5 cluster. prior to migrating phones, ive been asked to bring the firmware on our current phones up to the same default firmware on the 10.5 CUCM currently, my phones are on an old 8.0.3 system. the firware on these 69...

Justin Hale · 05-07-2013

Hi All,We are using MS OCS 2007 R2 and MOC 2007 R2.Everything has been working beautifully for a couple years and suddenly we are getting "No Phone System connection, the Call control server is temporarily unavailable"all SIP: and TEL: URI informatio...

Justin Hale · 04-09-2013

hi All,Im running CUCM 8.0.3Some users reported their phones stoped working. In CUCM the phones in question have a "Rejected" Status.i check RTMT and also see them Rejected and the apparent reason is "AuthenticationError".i just reset a previously re...

Justin Hale · 04-04-2018

Regarding the footnote "Changing the WLAN interface mapping in an AP Group will remove the local VLAN mapping for FlexConnect AP in this group. I have seen in some cases the local mappings are retained, and in some cases not. I don't know why! e....

Justin Hale · 04-14-2013

i have about 50 phone affected at a site which we recent decommishioned, however the phones are still there.The only way I can shutdown the phones is by cutting off PoE. however, it seems simply rebooting them is not making them come back up with th...

Justin Hale · 04-10-2013

Hi,I want to keep 9-0-3-0 for now. TFTP restarted.tried a hardware reset, but no good, had to do factory reset then it registered no problems.Are you sure you cannot use both methods at the same time?As examble 6941/6921 have issues with voice quali...

Justin Hale · 04-10-2013

The active phone load for the 3 test device is "SCCP69XX.9-3-3-2" there are no typo's i can see. all phones are 6941 and have the correct device type.i checked a phone that should not have the new image, but it looks like it does,..and the old image...

Justin Hale · 04-10-2013

HiSCCP69xx.9-0-3-0 is already in device defaults for 6921/6941/6961. i restarted TFTP services anyway. will get the users to reboot phones.my 3 test phones have SCCP69xx.9-3-3-2 in Phone Load Name and are working as expected.i cant explain what has h...

Member Since	‎05-15-2011 09:32 PM
Date Last Visited	‎06-06-2021 04:50 PM
Posts	27

User Statistics

User Activity

DOT1x and CDP Bypass suddenly not working

911 Issues

69xx Firmware issues

MOC Integration

6941 Rejected in CUCM

Re: Flexconnect\AP Group Question

6941 Rejected in CUCM

6941 Rejected in CUCM

6941 Rejected in CUCM

6941 Rejected in CUCM