Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About belemgarrido
Stats
Member since
11-25-2011
9
Posts
0
Helpful
0
Solutions
10-12-2012
09:22 AM
The problem was on the telephone firmware, the expansion module was on a 7962 which needs its firmware named SCCP42.8-5-2S. In the configuration above I had only the 7960-7940 firmware loaded that's why the expansion module couldn't register. Hope it works. Regards.
... View more
Created by
belemgarrido
in IP Telephony and Phones
in IP Telephony and Phones
09-06-2012
12:19 PM
09-06-2012
12:19 PM
Hi Rob, Thank you very much for your help. I changed the Device Defaults and reset the TFTP service and the phone register normally. Have a great weekend.
... View more
Created by
belemgarrido
in IP Telephony and Phones
in IP Telephony and Phones
09-06-2012
11:48 AM
09-06-2012
11:48 AM
Hi Rob, Thanks for your reply! I can't access the settings but the phone is looking for the file P00308010200.loads which is in the firmware version 8.0(10), the .loads file from the 8.1.1 firmware version is P00308010100 so I can't use the 8.1.1 version. I stopped and started the TFTP service but keeps failing. I really appreciate your help.
... View more
Created by
belemgarrido
in IP Telephony and Phones
in IP Telephony and Phones
09-06-2012
11:02 AM
09-06-2012
11:02 AM
Hi, I've upgraded to CUCM 8.5, the phones were working until I change a 7940 to another switch port, the phone indicates "File auth error" when tries to download its firmware from the TFTP server. I've tried to upgrade phone firmware from 8.0(10) to 8.1(1) and then to 8.2 but it doesn't work, I keep the 8.1(1) firmware version but keeps showing "File auth error". I've already modified the Device Defaults and erase/create the phone into the CUCM devices but keeps failing. Is there any workaround for this issue? Thanks for your help. Regards.
... View more
Labels:
06-13-2012
04:24 PM
Hi m.junghage, I already have the latest version of the phone and the expansion module. Any ideas?? Thanks!! Regards.
... View more
06-13-2012
04:22 PM
Hi aokanlawon, I ran the debug you asked me and there are no results, it seems that the expansion module is not asking for its firmware and same thing for the telephony-service tftp-bindings, I couldn't get the output of the tftp-bindings because the user is in a remote office. Any ideas about what's happening? Thank you very much.
... View more
06-11-2012
09:12 AM
Hi, I am configuring a 7915 module for a 7962G ip telephone on a CME. I'd configured the ephone and upload its firmware but the module shows at the screen the Cisco logo and all of the buttons are steady amber, all of them. Is there any configuration that I'm missing or this expansion module is defective? Thanks for your help. ############################### tftp-server flash:B015-1-0-2.SBN ! ! telephony-service ... load 7914 S00105000300 load 7915-12 B015-1-0-2 load 7911 SCCP11.8-4-2S load 7921 CP7921G-1.1.1 load 7937 apps37sccp.1-2-1-0 load 7960-7940 P00308000500 load 7945 SCCP45.8-4-2S ! ! ephone 85 device-security-mode none description Call Center mac-address ECC8.8211.BC6E after-hours exempt blf-speed-dial 1 350 label "Normita" blf-speed-dial 2 351 label "Dr.Ruiz" blf-speed-dial 3 228 label "Resultados" blf-speed-dial 4 352 label "SalaJuntas" paging-dn 234 type 7962 addon 1 7915-12 button 1:106 2:6 3:7 4:8 button 5:70 6:71
... View more
Labels:
Created by
belemgarrido
in Small Business Network and Smart Storage
in Small Business Network and Smart Storage
01-04-2012
11:57 AM
01-04-2012
11:57 AM
Hi, I am configuring a HotSpot with a Cisco SRP521W. I am using its USB port to connect a 3G USB Módem and to get access to an internal DNS Server with IP address 150.4.1.38 I use a VPN. The clients that uses the 3G connection are forced to use this DNS Server but I can´t achieve this task because I don't know how to permit only this DNS address. Using an IOS router the line would be: access-list extended permit udp any host 150.4.1.38 eq 53 Is there any way to configure this line on the Cisco SRP521W? Thanks for your help!
... View more
11-25-2011
12:03 PM
Hi, I am configuring a HotSpot with a Cisco SRP521W. I am using its USB port to connect a 3G USB Módem and to get access to an internal DNS Server with IP address 150.4.1.38 I use a VPN. The clients that uses the 3G connection are forced to use this DNS Server but I can´t achieve this task because I don't know how to permit only this DNS address. Using an IOS router the line would be: access-list extended permit udp any host 150.4.1.38 eq 53 Is there any way to configure this line on the Cisco SRP521W? Thanks for your help!
... View more
Labels:
10-12-2012
The problem was on the telephone firmware, the expansion module was on a
7962 which needs its firmwa...
09-06-2012
Hi Rob,Thank you very much for your help. I changed the Device Defaults
and reset the TFTP service a...
09-06-2012
Hi Rob,Thanks for your reply! I can't access the settings but the phone
is looking for the file P003...
09-06-2012
Hi,I've upgraded to CUCM 8.5, the phones were working until I change a
7940 to another switch port, ...
06-13-2012
Hi m.junghage,I already have the latest version of the phone and the
expansion module.Any ideas?? Th...
06-13-2012
Hi aokanlawon,I ran the debug you asked me and there are no results, it
seems that the expansion mod...
06-11-2012
Hi,I am configuring a 7915 module for a 7962G ip telephone on a CME. I'd
configured the ephone and u...
Created by
belemgarrido
in Small Business Network and Smart Storage
01-04-2012
01-04-2012
Hi,I am configuring a HotSpot with a Cisco SRP521W. I am using its USB
port to connect a 3G USB Móde...
Public Statistics
| Date Registered | 11-25-2011 11:18 AM |
| Date Last Visited | 08-18-2017 04:00 AM |
| Total Messages Posted | 9 |
.jpg "VIP Mentor"){kind=icon}
