Hello, The above configuration is only for sip phones to register in SRST. For Skinny you can use call-manager fall-back or CME-as-SRST. Below are the documents: Call-manager fallback: https://supportforums.cisco.com/document/98721/how-implement-cisco-unified-srst-and-mgcp-fallback CME as SRST: https://supportforums.cisco.com/document/98681/how-implement-cucme-srst-mode Hope this helps. -Kevin Monteiro ... View more

Hi MT, Attach the "show tech" of CME.Secondo you can configure Unity express via CLI or web using IP of the CUE on the web browser. Here is a link for your reference: http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unity-express/62609-tdcmecue.html -Kevin Monteiro ... View more

Hi MT, Use IE (Internet Explorer) in compatible mode. It should work. Rate the post accordingly. -Kevin Monteiro ... View more

 Nagaraj, Its as simple as this, if you have 31- Channels on the E1-PRI 30 B- channels and 1 D-channel for signalling. The concept is the same with dsp's "PVDM2-64" has 64 channels. So if you use 1 E1-port of the "VWIC2-2MFT-T1/E1" you'll consume 31 channels of the ""PVDM2-64" 64 - 31 if you using 2  E1 ports. Then this would be 62 Channels consumed of the "PVDM2-64". So yes would had to reduce or shutdown  the "conference/transcoder" resource on the Gateway. To answer your question about this affecting anything in SRST. No it wont affect anything. All you need to do it fix your dial-peers for incoming and outoing calls in SRST for the 2nd E1-PRI that you have configured. -Kevin Monteiro ... View more

Hey Mac-add of the phone. Attach the "show tech" and "debug ip dhcp server events" "debug ip dhcp server pac". "debug ccsip mess". -Kevin ... View more

Yep you need to get the routing fixed. -Kevin ... View more

Hello, To add to what Nadeem said "When a call comes in on an SIP trunk and gets forwarded (CFNA / CFB / CFA), then the default behavior is for the CME to send the 302 “Moved Temporarily” SIP message to the Service Provider (SP) proxy. The user portion of the Contact Header in the 302 message might need to be translated to reflect a DID that the SP proxy can route to . The host portion of the Contact Header in the 302 message should be modified to reflect the Address of Record (AOR) using the host-registrar CLI under sip-ua and the b2bua CLI under the VoIP dial peer going to the CUE. Some SIP proxies might not support this. If so, then you need to add this:" MS(config)#voice service voip MS(conf-voi-serv)#no supplementary-service sip moved-temporarily -Regards, Kevin ... View more

Hello, Looks like the "how tech" you attached didnt gather much information. Can you send me the "show tech" again. -Kevin ... View more

Yamikani, Send the following debugs: debug voip ccapi inout debug ccsip messages Check if its the same behaviour on internal calls also. Kindly attach the "show tech". -Kevin ... View more

Hello Can you post your configuration in here. -Kevin Monteiro ... View more

Hi Breeze, here is the link which should help you out: https://supportforums.cisco.com/document/12744371/cme-gui-trick Just wanted to share on CSC , as there have been many instances where most of customer or Tshoot engineers come with CME GUI files located in the flash as follows:   cme_gui.png   Generally we just extract the .tar file in VGW/CME which leads to the directory created in this format. Reason being if you open CME Gui tar which you have downloaded from Cisco.com you will see folder and sub-folder after untar the file CME-GUI.tar file. Now CME or VGW won’t you allow to configure the path for GUI files as below due to the space in between which is quite it will not understand the syntax and eventually you will get a syntax error like below   (config)#ip http path flash: CME 10.5.0 GUI                                                          ^ % Invalid input detected at ‘^’ marker.   To perform this task without making any changes in the file. There is a trick/workaround .   (config)#ip http path “flash: CME 10.5.0 GUI”     Notice, I have included the complete file path within inverted commas. This workaround works well and you won’t need to upload each GUI file one by one onto the flash. Just copy the GUI .tar file in flash, extract it in the gateway’s flash and use the workaround to specify the location of GUI files. Saves a lot of time.   Rate the post accordingly. -Kevin Monteiro ... View more