I have a Multi-Office network setup through our ISP. The network allows us to put what ever VLANs/Traffic on the connection we want.   The way it us Currently setup is we have SG500X units at each location. We Trunk the HQ Subnet (10.1.0.0/16) to each of the sites as well as a Subnet that is for Customers to use (192.168.1.0/24).   Each Site's SG500X then is setup for layer 3 Routing and Each office has its own Internal Subnet. Office 2 10.2.0.0/16 Office 3 10.3.0.0/16 etc   Each router is using RIP to broadcasts its subnets too the other, so when the Local 10.X.0.1 is used at each office it knows which 10.1.0.X SG500X to access to get to the other remote subnet.  Office 1 and 3 have an Internet Connections. Only Office 1 is used at the moment and I need to get Office 3 Online and Routing for Failover.    My Question is can I use the SG500X for this?  when I add a second default gateway the only one that shows up is the one with the lowest metric. The other does seem to be there in the CLI Config, though if I remove the Primary Gateway IP from service, I cant get the other sites to use the other Gateway IP that I put in there.     Can I use the SG500X for this? Do I need to go to a Catalyst style? Should I have the WAN Network setup Differently?   Thanks!   Scott<-       ... View more

I've upgraded a few 5506 ASAs (form 9.3, 9.5) to 9.8. I Migrated the Configs from the older style useless ports to a Bridge-group so I i can use all of the GE Ports.      interface GigabitEthernet1/<2-8> speed auto duplex auto no flowcontrol send on bridge-group 1 nameif inside_<2-7> no cts manual security-level 100 delay 1 ! interface Management1/1 speed auto duplex auto no flowcontrol send on management-only no nameif no cts manual no security-level no ip address delay 1 ! interface BVI1 nameif inside security-level 100 ip address 10.111.111.1 255.255.0.0 !   The VPN is up, I can pass VPN Traffic back and forth and all is good from remote clients on the other side of the inside interface of the Remote ASA.    I cannot however save my Config to my TFTP server on the HQ Connected TFTP server.  I can ping it using the internal interface. I have set (with inside and inside_1-Inside_7): tftp-server inside <IP of server> <filename>   I also can no longer telnet to the remote ASA from HQ's Management Subnet.  I have the following (with inside and inside_1-Inside_7): telnet NETWORK-OLIVET 255.255.0.0 inside telnet NETWORK-HBG 255.255.255.0 inside management-access inside  None work.    I can telnet and ssh to other devices on the remote network.      Copy of a sanitized config: : Saved : : Serial Number: JAD23080D24 : Hardware: ASA5506, 4096 MB RAM, CPU Atom C2000 series 1250 MHz, 1 CPU (4 cores) : ASA Version 9.8(2) ! hostname olivet domain-name <Our Domain> xlate per-session deny tcp any4 any4 xlate per-session deny tcp any4 any6 xlate per-session deny tcp any6 any4 xlate per-session deny tcp any6 any6 xlate per-session deny udp any4 any4 eq domain xlate per-session deny udp any4 any6 eq domain xlate per-session deny udp any6 any4 eq domain xlate per-session deny udp any6 any6 eq domain names name <Subnet of HBG> NETWORK-HBG name <Subnet of Olivet> NETWORK-OLIVET name <IP of TFTP Server> <Name of TFTP Server> name <IP of SYSLOGD Server> <Name of SYSLOGD Server> ! interface GigabitEthernet1/1 nameif outside security-level 0 ip address <Comcast IP Address> 255.255.255.0 ! interface GigabitEthernet1/2 bridge-group 1 nameif inside_1 security-level 100 ! interface GigabitEthernet1/3 bridge-group 1 nameif inside_2 security-level 100 ! interface GigabitEthernet1/4 bridge-group 1 nameif inside_3 security-level 100 ! interface GigabitEthernet1/5 bridge-group 1 nameif inside_4 security-level 100 ! interface GigabitEthernet1/6 bridge-group 1 nameif inside_5 security-level 100 ! interface GigabitEthernet1/7 bridge-group 1 nameif inside_6 security-level 100 ! interface GigabitEthernet1/8 bridge-group 1 nameif inside_7 security-level 100 ! interface Management1/1 management-only no nameif no security-level no ip address ! interface BVI1 nameif inside security-level 100 ip address <Subnet of Olivet>.1 255.255.0.0 ! ftp mode passive clock timezone PST -8 clock summer-time PDT recurring dns domain-lookup inside dns server-group DefaultDNS domain-name <Our Domain> same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network obj_any1 subnet 0.0.0.0 0.0.0.0 object network obj_any2 subnet 0.0.0.0 0.0.0.0 object network obj_any3 subnet 0.0.0.0 0.0.0.0 object network obj_any4 subnet 0.0.0.0 0.0.0.0 object network obj_any5 subnet 0.0.0.0 0.0.0.0 object network obj_any6 subnet 0.0.0.0 0.0.0.0 object network obj_any7 subnet 0.0.0.0 0.0.0.0 object network obj_any subnet 0.0.0.0 0.0.0.0 object network NETWORK-HBG subnet <subnet of HBG> 255.255.0.0 object network NETWORK-OLIVET subnet <Subnet of Olivet> 255.255.0.0 object-group network NETWORK_LOCAL description Local Networks network-object object NETWORK-OLIVET object-group network NETWORK_REMOTE description Remote Networks network-object object NETWORK-HBG access-list outside_cryptomap_1 extended permit ip object-group NETWORK_LOCAL object-group NETWORK_REMOTE pager lines 54 logging enable logging timestamp logging list xlate-log message 202001 logging list xlate-log message 305009-305012 logging list SMTP-log message 108002 logging list startup-log message 199001-199005 logging list GRE-log message 302017-302018 logging list verifycertdn-log message 320001 logging list IDS-log message 400000-400050 logging list sa-log message 602201 logging list sa-log message 602301-602302 logging list VPNCLIENT-log message 611301-611323 logging list ISAKMP-log message 702201-702212 logging list IPSecConnect-log message 113019 logging list MISC-Log message 713900-713906 logging list acl-drop message 106023 logging list acl-drop message 106100 logging list acl-drop message 106104 logging buffer-size 1048576 logging console notifications logging monitor informational logging buffered debugging logging trap informational logging asdm warnings logging mail warnings logging from-address olivet@eandm.com logging recipient-address scott@eandm.com level errors logging device-id hostname logging host inside <IP of SYSLOGD Server> logging debug-trace logging permit-hostdown no logging message 305012 no logging message 305011 no logging message 302015 no logging message 302014 no logging message 302013 no logging message 304001 no logging message 609002 no logging message 609001 no logging message 302016 no logging message 302021 no logging message 302020 logging message 305012 level warnings logging message 305010 level warnings logging message 305009 level warnings logging message 302013 level warnings mtu outside 1500 mtu inside_1 1500 mtu inside_2 1500 mtu inside_3 1500 mtu inside_4 1500 mtu inside_5 1500 mtu inside_6 1500 mtu inside_7 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected arp rate-limit 16384 nat (inside_1,outside) source static NETWORK_LOCAL NETWORK_LOCAL destination static NETWORK_REMOTE NETWORK_REMOTE no-proxy-arp route-lookup description No not NAT traffic to/from Remote Networks nat (inside_2,outside) source static NETWORK_LOCAL NETWORK_LOCAL destination static NETWORK_REMOTE NETWORK_REMOTE no-proxy-arp route-lookup description No not NAT traffic to/from Remote Networks nat (inside_3,outside) source static NETWORK_LOCAL NETWORK_LOCAL destination static NETWORK_REMOTE NETWORK_REMOTE no-proxy-arp route-lookup description No not NAT traffic to/from Remote Networks nat (inside_4,outside) source static NETWORK_LOCAL NETWORK_LOCAL destination static NETWORK_REMOTE NETWORK_REMOTE no-proxy-arp route-lookup description No not NAT traffic to/from Remote Networks nat (inside_5,outside) source static NETWORK_LOCAL NETWORK_LOCAL destination static NETWORK_REMOTE NETWORK_REMOTE no-proxy-arp route-lookup description No not NAT traffic to/from Remote Networks nat (inside_6,outside) source static NETWORK_LOCAL NETWORK_LOCAL destination static NETWORK_REMOTE NETWORK_REMOTE no-proxy-arp route-lookup description No not NAT traffic to/from Remote Networks nat (inside_7,outside) source static NETWORK_LOCAL NETWORK_LOCAL destination static NETWORK_REMOTE NETWORK_REMOTE no-proxy-arp route-lookup description No not NAT traffic to/from Remote Networks ! object network obj_any1 nat (inside_1,outside) dynamic interface object network obj_any2 nat (inside_2,outside) dynamic interface object network obj_any3 nat (inside_3,outside) dynamic interface object network obj_any4 nat (inside_4,outside) dynamic interface object network obj_any5 nat (inside_5,outside) dynamic interface object network obj_any6 nat (inside_6,outside) dynamic interface object network obj_any7 nat (inside_7,outside) dynamic interface route outside 0.0.0.0 0.0.0.0 <Comcast GW IP on Outside Interface> 1 timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 sctp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 timeout conn-holddown 0:00:15 timeout igp stale-route 0:01:10 user-identity default-domain LOCAL aaa authentication login-history http server enable http NETWORK-HBG 255.255.0.0 inside_1 http NETWORK-OLIVET 255.255.0.0 inside_1 no snmp-server location no snmp-server contact service sw-reset-button crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map1 1 match address outside_cryptomap_1 crypto map outside_map1 1 set peer <IP of HQ ASA> crypto map outside_map1 1 set ikev1 phase1-mode aggressive crypto map outside_map1 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map1 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map1 interface outside crypto ca trustpool policy crypto isakmp identity hostname crypto ikev1 enable outside crypto ikev1 policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet NETWORK-OLIVET 255.255.0.0 inside_1 ! Limiting to 255.2555.255.0 Subnet for Management IPs only vs 255.255.0.0 telnet NETWORK-HBG 255.255.255.0 inside_1 telnet timeout 25 ssh stricthostkeycheck ssh timeout 5 ssh key-exchange group dh-group1-sha1 console timeout 0 management-access inside threat-detection basic-threat no threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server <NTP Server> source outside prefer tftp-server inside <IP of TFTP Server> remoteASA-2019.0426.02.cfg group-policy <IP of HQ ASA> internal group-policy <IP of HQ ASA> attributes vpn-idle-timeout 35791394 dynamic-access-policy-record DfltAccessPolicy tunnel-group <IP of HQ ASA> type ipsec-l2l tunnel-group <IP of HQ ASA> general-attributes default-group-policy <IP of HQ ASA> tunnel-group <IP of HQ ASA> ipsec-attributes ikev1 pre-shared-key ***** ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns migrated_dns_map_1 parameters message-length maximum 1024 no tcp-inspection policy-map global_policy class inspection_default inspect ftp inspect http inspect ils inspect rsh inspect rtsp inspect skinny inspect sunrpc inspect tftp inspect xdmcp inspect netbios inspect dns migrated_dns_map_1 ! service-policy global_policy global prompt hostname context no call-home reporting anonymous event manager applet VPN-Always-UP event timer watchdog time 60 action 1 cli command "ping inside <HQ IP>" output none : end ... View more

Head End:Cisco ASA 5525-X -  9.4(1) Remote Site A: Cisco ASA5506 - 9.5(1) Remote Site B: Cisco ASA5506 - 9.2.4(18) AnyConnect Client: iPad v4.0.05066 I want to be able to Connect to the Remote Site from the AnyConnect Client. from the Remote site I can Ping the IP address of the iPad's VPN Connection and it pings fine. Turn off the VPN and the Ping Dies.  I Only have the iPad at this point to Test. So I am limited to what I can initiate from the remote site to the AnyConnect Client.  From the AnyConnect Client to the HQ site works great, though any Pinging, RDP, or anything that Originates from the AnyConnect Client to the Remote site fails.  Remote Site A and Remote site B can both ping back and forth.  I'm sure its part of the Crypto Access Lists that are not right, though I can't tell if I'm not getting let in at the remote sites, or if the Head end is blocking it from going out. or If its a NAT thing or? I thought about posting configs and having someone point out my obvious mistakes, though I want to get better at debugging this kind of stuff. What are some good debug commands to see where this connection is failing? Thank you,   Scott<- ... View more

I wanted to Upgrade my 5505 from  8.3.2 to 9.2.4(18) so I could get access to the EEM.  After the Upgrade I Lost my VPN to the HQ Office.  the upgrade log didn't have anything in it, and comparing the config files before and after there were not really any changes. here is the upgrade_startup_errors log file INFO: MIGRATION - Saving the startup errors to file 'flash:upgrade_startup_errors_201701242240.log' Reading from flash... !! INFO: MIGRATION - Saving the startup configuration to file INFO: MIGRATION - Startup configuration saved to file 'flash:8_3_2_0_startup_cfg.sav' *** Output from config line 4, "ASA Version 8.3(2) " WARNING: interface Vlan2 security level is 0. *** Output from config line 135, "logging host outside vsv..." I know enough to be dangerous, though all of my normal debug commands didn't seem to produce any VPN debugging output.  I did the 'term mon' and could see other output, but nothing from the VPN Debugging: debug crypto ipsec debug crypto isakmp debug crypt engine After some time of troubleshooting I then backed out the firmware and ASDM and then copied back in the config from the 8.3.2 firmware.  Still no VPN Connection coming up.  I've checked the SAs at the HQ Site and its not holding on to anything, nothing on the Log on the HQ End.  Not sure where to go from here. )-: Thanks!   Scott<- ... View more