Dear Support community I am facing strange issue in my network. I am not able to ssh/telnet any device in the same network. I am able to ping all the devices. kindly please suggest the solution.
Thanks and Regards
... View more
Thanks John for the sample configuration and advice, I am Getting Below Error.
%SW_DAI-4-DHCP_SNOOPING_DENY: 1 Invalid ARPs (Req) on Gi3/2, vlan 183.([0003.472d.8b0f/10.10.10.62/0000.0000.0000/10.10.10.2/12:19:27 UTC Wed Apr
Also in the design I mention
HOST----------(Gi1/2)Switch1(Ten5/1)-----------(Ten5/1)CORE(Ten1/1)----------DHCP SERVER
My Layer 3 Interface is on Core, so switch 1 is just layer 2 device. So will suggested configuration will work with this design??
Please advice.
... View more
Dear Friends
I am have Issue with Dynamic Arp Inspection. Below is my Network Diagram.
HOST----------(Gi1/2)Switch1(Ten5/1)-----------(Ten5/1)CORE(Ten1/1)----------DHCP SERVER
My host is in vlan 10, I have configured "ip arp inspection vlan 10" on switch1 and also configure "ip arp inspection trust" on interface Ten5/1 on Switch1 and Interface Ten5/1 on Core.
But problem is my host is not able to get ip from dhcp server.
If i remove "ip arp inspection vlan 10" from switch one, host gets ip from DHCP.
Please Advice.
... View more
Dear Friend
Recently I have installed Cisco Prime Infrastructure 3.0 for one of our customer. I add the devices and now I did configuration archive for some devices to backup the configuration. kindly please tell, cisco prime infrastructure 3.0 by default were does it save this configuration archive of the devices and how can I access it.
Regards
Abbas M. Ravat
... View more
Dear All
I have Router (Cisco 2811), it was working fine and now i am not able to SSH/Telnet to this Device. While trying to telnet or SSH it says "connection timed out; remote host not reponding".
Please help with suggestion what could be the issue.
Thanks.
Abbas
... View more
Dear All,
I have CCVP certification, now I want to renew my CCVP certificate to CCNP Collaboration. How can I upgrade to this certification.
In CCVP Exam I have given was as below.
642-456 CIPT2
642-446 CIPT1
642-436 CVOICE
642-426
Kindly please advice. which exam i have to appear to renew my CCVP certificate.
... View more
Hello Everyone; I have two cisco 6509-E catalyst chassis with Dual VS-SUP2T-10G Supervisor Engineen each. All VS-SUP2T-10G have IOS: s2t54-ipservicesk9-mz.SPA.150-1.SY3.bin. Before I configured VSS all modules working ok on both chassis, Below is show module output. Router#sh mod Mod Ports Card Type Model Serial No. --- ----- -------------------------------------- ------------------ ----------- 1 16 CEF720 16 port 10GE WS-X6816-10GE SAL1648TBZ3 3 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6848-GE-TX SAL1649TRTA 4 8 Network Analysis Module WS-SVC-NAM-2-250S SAL1646S846 5 5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G SAL1643R23B 6 5 Supervisor Engine 2T 10GE w/ CTS (Hot) VS-SUP2T-10G SAL1642Q7PR Mod MAC addresses Hw Fw Sw Status --- ---------------------------------- ------ ------------ ------------ ------- 1 e4d3.f1d8.3970 to e4d3.f1d8.397f 1.1 12.2(18r)S1 15.0(1)SY3 Ok 3 001f.6ca5.0038 to 001f.6ca5.0067 1.0 12.2(18r)S1 15.0(1)SY3 Ok 4 f0f7.5569.1478 to f0f7.5569.147f 1.2 7.2(1) 5.1(1) Ok 5 e05f.b911.5c9a to e05f.b911.5ca1 1.3 12.2(50r)SYS 15.0(1)SY3 Ok 6 e05f.b911.4d18 to e05f.b911.4d1f 1.3 12.2(50r)SYS 15.0(1)SY3 Ok Mod Sub-Module Model Serial Hw Status ---- --------------------------- ------------------ ----------- ------- ------- 1 Distributed Forwarding Card WS-F6K-DFC4-E SAL1631JMV6 1.2 Ok 3 Distributed Forwarding Card WS-F6K-DFC4-A SAL1647STN9 1.0 Ok 5 Policy Feature Card 4 VS-F6K-PFC4 SAL1642QDJV 1.2 Ok 5 CPU Daughterboard VS-F6K-MSFC5 SAL1643R1RR 1.4 Ok 6 Policy Feature Card 4 VS-F6K-PFC4 SAL1642Q6F7 1.2 Ok 6 CPU Daughterboard VS-F6K-MSFC5 SAL1642Q3VP 1.4 Ok Mod Online Diag Status ---- ------------------- 1 Pass 3 Pass 4 Pass 5 Pass 6 Pass After I Configured VSS, standby VS-SUP2T-10G is not boot and it goes to rommon:. If I force with boot command it gives below mentioned log. *Feb 6 15:18:10.691: %PFREDUN-SW1_STBY-6-STANDBY: Initializing as STANDBY processor for this switch *Feb 6 15:18:11.067: %SYS-SW1_STBY-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output. *Feb 6 15:18:11.075: SW1_STBY: vs_ha_send_hb_start_msg:Sending start req with MyEobcAddr : 262 Frequency : 1000 Timeout : 179000 Version : 1 *Feb 6 15:18:11.075: SW1_STBY: vs_ha_ps_bootup_icc_msg_hdlr:** PSEUDO STDBY NOT SUPPORTED DROPPING TO ROMMON ** *Feb 6 15:18:11.075: %PFREDUN-SW1_STBY-4-SUP_FORCE_TO_ROMMON: Supervisor forced to rommon with reason: Cannot continue... disabling autoboot and resetting Kindly help and advice.
... View more
Dear All, I am facing problem with WCS Apache server, I have error Apache.exe: could not determine the server fully qualified domain name...Error. Apache service is stopped. Its WCS 4.2.62.11 WCSStatus shows: Database server is running Apache server is Stopped WCS is stopped. Kindly advice.
... View more
Dear Gajana Thanks for reply, Attached document for Upgrade to 6.1(1b) says this upgrade from 6.0(1) or 6.0(1a). What i have is version 6.0(1b) as my current version and from this version I want to upgrade to 6.1(1b). Document you send does not mention upgrade from 6.0(1b). Kindly Advice.
... View more
HI David Thanks for the reply. I am doing upgrade on existing hardware. Can you please advice how i can upgrade from version 6.0.1.3000-7 to 6.1.1.3000-2 that is 6.0(1b) to 6.1(1b). Thanks
... View more
Dear All I want to upgrade CUCM 6.0.1.3000-7 [ 6.0(1b)] to CUCM ver 8.6. now there is no direct upgrade to 8,6 from version 6.0. Upgrade path is 6.0.1.3000-7 to 6.1.1.3000-2 6.1.1.3000-2 to 6.1.3.3000-1 6.1.3.3000-1 to 6.1.4.2190-3 and then 6.1.4.2190-3 to 8.6 Now I am about to upgrade first stage that is 6.0.1.3000-7 to 6.1.1.3000-2. Kindly please can you help me step by step on how can I carry this 1st stage of upgrade. your immediate reply is highly appericated. Thanks you.
... View more
Phone model is 7942 and firmware is SCCP42.9-1-1SR1S and even i cannot see corporate directory on this perticular phone it says host not found.
... View more