Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Angelo ANELLO
08-18-2017
Stats
Member since
08-08-2011
43
Posts
0
Helpful
0
Solutions
Created by
Angelo ANELLO
in Network Management
in Network Management
10-12-2014
10:26 PM
10-12-2014
10:26 PM
hi guys, as the title says, i recently installed a HWIC card into our 2801 router running IOS 12.4(24)T8. The card is recognized by the router and is set to GigabitEthernet 0/3/0. I enter the interface mode and apply commands and they are fine except when i try to apply the 'speed' and 'duplex' commands. they are not available under this interface and im not sure why nor am i sure how to rectify it. it is currently not connected only installed. has anyone else come across this issue before? does anyone have any idea how to fix it so that i can set the speed and duplex? does the cable need to be connected to the interface before i can assign these settings? here are the current interface settings: interface GigabitEthernet0/3/0 description WAN Link bandwidth 100000 ip address x.x.x.x x.x.x.x ip flow ingress shutdown no negotiation auto your help is appreciated regards
... View more
Labels:
Created by
Angelo ANELLO
in Network Management
in Network Management
09-25-2014
07:13 PM
09-25-2014
07:13 PM
Hi Guys, I have a 2801 router that i want to install a HWIC-1GE-SFP into and it is currently running IOS ver. 12.4(21a) spservicesk9 and i would like to know how to determine if a IOS revision is compatible. I have read this article to gain info regarding the min. reqs : http://www.cisco.com/c/en/us/products/collateral/routers/2800-series-integrated-services-routers-isr/product_data_sheet0900aecd8016be8d.html It states that the minimum firmware is 12.4(15)T9 which is lower than my current firmware however, the HWIC card is not being recognised. Is this due to the 'T' stream of firmware required since my IOS doesnt have this appended to it even though it is a higher revision? I have this version, 12.4(22)YB8, and would like to know if this is going to be compatible or not? I would really like to know how to determine this? Is there a list of features associated with the different streams of IOS i can refer to? Thanks for your help guys.
... View more
- Tags:
- ios 2801 router
Labels:
05-30-2013
07:10 PM
Hi Robert, thanks for your reply. Your answer is very informative. I have attached a graph below of a recent bandwidth test on a particular link we have at one remote site. I have removed the QoS from the remote router as well as any corresponding QoS config from our primary router but it looks as though the link is still suffering from the symptoms of policing above. What do you think? Thanks,
... View more
05-29-2013
06:03 PM
Hi Guys, We are looking to implement a bandwidth policy for our Internet link. What i would like to know is if we use a policing policy, will the exceeded dropped packets be resubmitted from the source? Will the dropped packets be resubmitted? Are there any differences besides this when using either policing or shaping policies? Is one better than the other? CISCO ASA 5510 IOS 8.2 Your help is appreciated. Regards,
... View more
Labels:
04-23-2013
05:16 PM
Hi Guys, We are in the process of upgrading our WAN links and on our WAN interfaces we have a bandwidth value that needs to be changed to reflect the ISP connection link. What i would like to know is how can we test the bandwidth of a WAN link before and after we change the values? This way we can get an idea of the performance figures. Our setup: We have a router that sits in the middle of our LAN switches and ISP WAN router. One interface connected to the LAN. The other connected to the ISP WAN router. It is this port and router that the WAN bandwidth values are being changed on. We do not have access to the WAN ISP router. Your help is appreciated Regards,
... View more
Labels:
04-07-2013
04:58 PM
Hi Guys, I have the following QoS settings applied within our routers and was wondering if we could tweak it further. Our settings are to prioritise Citrix and Printing traffic. What i would like to know is if it is possible to add further priorities within just the Citrix settings. As you can see, Citrix will encompass alot of traffic including our Email traffic and we would like to know if it is at all possible to achieve this. Below is the current config and any assistance is greatly apprecaited: class-map match-any Citrix match access-group name Citrix-ACL policy-map WAN class Citrix priority percent 80 set dscp af41 class class-default bandwidth remaining percent 100 fair-queue policy-map Global class class-default shape average 2048000 service-policy WAN Service-policy output Global (applied to WAN interface) Regards,
... View more
Labels:
03-26-2013
06:44 PM
Hi Leo, We currently have an HWIC-4ESW installed. Will this work? Thanks,
... View more
03-26-2013
06:28 PM
Hi Guys, We have a requirement to add a connection to our existing 2801 router, running 12.4 IOS, to service an Internet connection. Currently, the two built-in FA interfaces are being utilised for the following: FA 0/0 - Internal LAN connection FA0/1 - WAN connection We would like to use an expansion card that we have to give us an extra FA port to connect directly to the internet and use this router as our DMZ as well. Would there be an issue using this expansion card for this purpose? Can anyone give me an idea of the cpu load that this may cause? Is this even possible? At the moment we have a second router that is connected and is acting as our DMZ but we would like to remove this router and utilise the one router for all services. Any help/feedback is appreciated Regards,
... View more
Labels:
02-18-2013
04:09 PM
Just wanted to know if there is the possibility of creating QoS rules for Symantec Endpoint Protection so that when end devices are updating over the network, it doesnt hog the bandwidth. We are currently QoS'ing for Print and Citrix traffic. The only info i can find is that it uses TCP but this doesnt help. I also have the server port number but the destination ports are always different. Routers have IOS from 12.2 - 15.1 and are 2801 and 881 models. Any feedback is appreciated Regards,
... View more
Labels:
Created by
Angelo ANELLO
in Other Network Architecture Subjects
in Other Network Architecture Subjects
02-11-2013
03:32 PM
02-11-2013
03:32 PM
ok thanks i will try that out. One last thing, if i remove the CF card permanently is it possible to boot from USB and go straight to login without having to enter the following command, boot flash:filename.bin, after the router is powered on? Can the USB act as the CF card and be the only source of flash memory available in the router? Thanks,
... View more
Created by
Angelo ANELLO
in Other Network Architecture Subjects
in Other Network Architecture Subjects
02-10-2013
09:50 PM
02-10-2013
09:50 PM
I read somewhere in a cisco forum discussion that any bootloader higher than my current version is not compatible with 2801 version, only 2811 and 2821 can use the higher versions. Is this true? The reason i ask is that i have already tried to upgrade to version T11 and when rebooting, it gets stuck trying to upgrade the boot loader. I then have to reboot manually and it reverts to the original version. Have you ever come across this? Also, is the boot command from ROMMON or from the CLI? Thanks again
... View more
Created by
Angelo ANELLO
in Other Network Architecture Subjects
in Other Network Architecture Subjects
02-10-2013
09:29 PM
02-10-2013
09:29 PM
Thanks for the reply. Below is the bootstrap. Our router only has 128Mb RAM and 64Mb CF Memory, so we are limited in which IOS we can use. I have found the below version to be the newest based on our routers specs. The bootstrap has also been loaded and is compatible with the IOS version. USB device when plugged in is identified, this is not the issue. I plugged in the USB stick and copied a valid image file on it, however, when i reboot the router it goes the ROMMON prompt only. i have to manually boot the system from USB. Can i make the default boot device the USB stick and not the flash card? Cisco IOS Software, 2801 Software (C2801-SPSERVICESK9-M), Version 12.4(18e), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Mon 02-Mar-09 04:13 by prod_rel_team ROM: System Bootstrap, Version 12.4(13r)T5, RELEASE SOFTWARE (fc1) GLOBALSW-PRIMARY-RTR uptime is 3 minutes System returned to ROM by power-on System image file is "flash:c2801-spservicesk9-mz.124-18e.bin" Cisco 2801 (revision 4.1) with 115712K/15360K bytes of memory. Processor board ID FHK084010NJ 6 FastEthernet interfaces 1 Serial(sync/async) interface DRAM configuration is 64 bits wide with parity disabled. 191K bytes of NVRAM. 62592K bytes of ATA CompactFlash (Read/Write) Configuration register is 0x2102
... View more
Created by
Angelo ANELLO
in Other Network Architecture Subjects
in Other Network Architecture Subjects
02-10-2013
04:41 PM
02-10-2013
04:41 PM
Hi Guys, just wanted to know if it is possible to use the usbflash0: port to boot the IOS on a permanent basis? Will the system reboot and load the IOS automatically or does it always default to ROMMON mode and require a manual start? Is the USB port only for emergency situations? I am unable to find a definitive answer online. Using 2801 CISCO router IOS 12.4 and comp-atible ROMMON image to acknowledge USB flash. Your feedback is appreciated Regards,
... View more
Labels:
02-04-2013
05:14 PM
i will try this and continue to monitor the routers for any further issues. once confirmed i can close this request.
... View more
01-29-2013
09:24 PM
i had assumed this may be the case but can you provide any supporting documentation or link to some so that i can use it to proceed with upgrading the devices?
... View more
Created by
Angelo ANELLO
in Network Management
10-12-2014
10-12-2014
hi guys, as the title says, i recently installed a HWIC card into our
2801 router running IOS 12.4(2...
09-25-2014
Hi Guys, I have a 2801 router that i want to install a HWIC-1GE-SFP into
and it is currently running...
05-30-2013
Hi Robert, thanks for your reply. Your answer is very informative. I
have attached a graph below of ...
05-29-2013
Hi Guys, We are looking to implement a bandwidth policy for our Internet
link. What i would like to ...
04-23-2013
Hi Guys, We are in the process of upgrading our WAN links and on our WAN
interfaces we have a bandwi...
04-07-2013
Hi Guys, I have the following QoS settings applied within our routers
and was wondering if we could ...
03-26-2013
Hi Guys, We have a requirement to add a connection to our existing 2801
router, running 12.4 IOS, to...
02-18-2013
Just wanted to know if there is the possibility of creating QoS rules
for Symantec Endpoint Protecti...
Created by
Angelo ANELLO
in Other Network Architecture Subjects
02-11-2013
02-11-2013
ok thanks i will try that out.One last thing, if i remove the CF card
permanently is it possible to ...
Created by
Angelo ANELLO
in Other Network Architecture Subjects
02-10-2013
02-10-2013
I read somewhere in a cisco forum discussion that any bootloader higher
than my current version is n...
Created by
Angelo ANELLO
in Other Network Architecture Subjects
02-10-2013
02-10-2013
Thanks for the reply. Below is the bootstrap. Our router only has 128Mb
RAM and 64Mb CF Memory, so w...
Created by
Angelo ANELLO
in Other Network Architecture Subjects
02-10-2013
02-10-2013
Hi Guys, just wanted to know if it is possible to use the usbflash0:
port to boot the IOS on a perma...
02-04-2013
i will try this and continue to monitor the routers for any further
issues.once confirmed i can clos...
Public Statistics
| Date Registered | 08-08-2011 11:55 PM |
| Date Last Visited | 08-18-2017 04:00 AM |
| Total Messages Posted | 43 |
.jpg "Hall of Fame Community Legend"){kind=icon}
.jpg "VIP Advisor"){kind=icon}
