About chrisayres

chrisayres · 03-01-2021

Hi AllDo ISR4331's support the MPLS L3 VPN MIBI have an 4331 using IPBaseWhen I type "sho snmp mib | i L3Vpn" I get no responseAlso a MIB walk returns nothing

chrisayres · 11-22-2017

Hi, Can anyone tell me how to do the below (or point me to the correct config guide) I would like to configure a QOS priority Q on a 6832, but also have this Q policed so it cannot starve the other Q's (ie LLQ)

chrisayres · 06-30-2015

Hi we are replacing 3750's with 3650's and the ports on the new switches are behaving a bit strange.End devices that worked fine on 3750's are having connectivity issues on the 3650'sSee below output from a 3650How can the port be running at half dup...

chrisayres · 05-29-2015

Hi,I am dynamically applying PBR to a virtual-access int via AV Pairs.However not all traffic that should be policy routed is being, some is rejected and normal routed, If I remove CEF from the virtual-template nothing is PBR'd so it is definitely do...

chrisayres · 06-01-2014

Hi,Does anyone know why "show inv | exclude PID: " works correctly as belowIHPR10_A_CC375_06#sho inv | e PID:NAME: "1", DESCR: "WS-C3750-24TS"NAME: "GigabitEthernet1/0/1", DESCR: "1000BaseSX SFP"NAME: "GigabitEthernet1/0/2", DESCR: "10/100/1000BaseTX...

chrisayres · 11-22-2017

By the way, I have tried priority level {1|2} [percent percentage ] But however much traffic a throw through that Q with a traffic generator I can't get the Q to drop the traffic above the set percent value

chrisayres · 05-29-2015

Hi, yep I suspected as much. I moved the policy onto the virtual-template and got the same results.I will get TAC onto it

chrisayres · 06-02-2014

Hi Rick, thanks for you reply,Possibly, but the below worksIHPR10_A_CC375_06#sho inv | i PID: (with a whitepace after the colon)PID: WS-C3750-24TS-S , VID: V05, SN: CAT0931N110PID: , VID: 14 , SN: FNS112505E2PID: , VID: 255, SN: AGM163923J...

chrisayres · 03-28-2011

Not really, but I found the answer, after the router directly connected to the source receieves a register stop message it sets a 1 minute suppression timer and sends a null message 5 seconds before this expires. If the RP doesn't reply to this the s...

chrisayres · 01-13-2011

This has been bugging me all afternoon, In an attempt to understand what is going on I put the below inbound on F0/0 and hey presto it works. I have to log the ACL though or it doesn't work. Something to do with how the packets are processed I expect...

Member Since	‎02-12-2002 03:06 AM
Date Last Visited	‎03-01-2021 07:59 AM
Posts	149
Total Helpful Votes Received	5

User Statistics

User Activity

ISR4331 MPLS-L3-VPN MIB Support

Cisco C6832-X-LE (15.2) Priority Q Policing

Strange Cat 3650 port behaviour

PBR and Virtual Interfaces

IOS Output Modifiers Strange Behaviour

Re: Cisco C6832-X-LE (15.2) Priority Q Policing

Hi, yep I suspected as much.

Hi Rick, thanks for you reply

Re: PIM Sparse Question

Re: EasyVpn Question