About DOUGLAS DRURY

DOUGLAS DRURY · 07-18-2019

A 3rd party has asked me to open a range of ports for a new phone system they are installing. However, I can't figure out how to open a range of ports on my Cisco 1921. They are asking me to open ports 10000 to 20000 I have done this for port 5060 ...

DOUGLAS DRURY · 11-09-2017

Hi All. I’m looking for some help with SIP/VOIP prioritization on my Cisco 887va. We have a remotely hosted SIP phone system. The problem is when we are working on PC’s for clients and they start to download updates for Windows 10 we are getting ...

DOUGLAS DRURY · 02-13-2017

Hi All, One morning my client said they had no internet when I got there Dialer1 had no IP address. I tried disconnecting the DSL cable, shutting down the Dialer1 then no shut, also tried rebooting the router with no success. I called the provider...

DOUGLAS DRURY · 07-01-2016

Hi, I'm having some trouble setting up VRF on a Cisco 1921. The router has 2 VDSL card installed. The ISP has only been able to active 1 of the FTTC lines however, the Dialer2 isn't connecting/getting an IP. I've tested the line with the free rou...

DOUGLAS DRURY · 04-07-2016

Hi, I've configured a Cisco 887va router with a set of Cisco 2960-S switches. The problem is anyone on VLAN 30 is not getting an IP address. VLANs 10 & 25 are getting IP addresses fine from my laptop acting as a DHCP server. But VLAN 30 are not ge...

DOUGLAS DRURY · 11-10-2017

Hi, Thanks for your help so far. I tried to add shape average 20000000 in the parent policy but the router rejected it with % Invalid input detected at '^' marker. The marker was at shape Below is my configuration. RT#sh run brBuilding con...

DOUGLAS DRURY · 11-10-2017

Hi, I tried your suggestion and got the below for each of the interfaces. It hasn't applied to any of the interfaces RT(config-if)#service-policy output VOIPQOS_PARENTCannot attach queuing-based child policy to a non-queuing based classRTconfig-...

DOUGLAS DRURY · 11-10-2017

Hi, I couldn't apply it to the dialer interface anyway because the router rejected the command with the error: Flow Fair Queueing feature is not supported in default class of parent level policy of. Thanks

DOUGLAS DRURY · 11-10-2017

Thanks for the reply. I'm using IOS: System image file is "flash:c880data-universalk9-mz.153-3.M9.bin" When I tried to apply the command to the interface I go the below. I'm on a VDSL line so I use Ethernet0.101 RT(config)#inter ethernet 0.101RT...

DOUGLAS DRURY · 03-01-2017

Can anybody offer up some advide as to how to fix this problem. I've erased the config and started again but still not getting an IP. when i do a sh ip int br i can see under the dialer interface it's set to either manual or NVRAM not IPCP as it ...

Member Since	‎07-22-2012 12:44 AM
Date Last Visited	‎07-25-2019 04:12 AM
Posts	107
Total Helpful Votes Received	10

User Statistics

User Activity

Open Range of Ports For NAT

SIP QOS on CIsco 887VA Help

Dialer not getting showing IP Address from Provider

Dialer not connecting with VRF

Cisco 887 & 2960-S DHCP snooping problem

Re: SIP QOS on CIsco 887VA Help

Re: SIP QOS on CIsco 887VA Help

Re: SIP QOS on CIsco 887VA Help

Re: SIP QOS on CIsco 887VA Help

Can anybody offer up some