About ricardorojas123

ricardorojas123 · ‎08-28-2013

Hi, I have the last question, if the primary supervisor fails (slot03), Can I connect the uplinks from the port 01 and port 02 of the slot03 to port03 and port04 of the slot04?, the supervisor in the slot04 will be the new primary supervisor .

ricardorojas123 · ‎08-23-2013

you're right, this design does not have high availability. you can give me any suggestions?

ricardorojas123 · ‎08-23-2013

Hi, So, The uplink of the 3750-01 is connected to Port 01 of Primary Supervisor. The uplink of the 3750-02 is connected to Port 02 of Primary Supervisor. The uplink of the 3750-03 is connected to Port 01 of Standby Supervisor. The uplink of the 3750-04 is connected to Port 02 of Standby Supervisor. And then enter the command #hw-module uplink select gigabitethernet ??

ricardorojas123 · ‎08-23-2013

Hi, I have a new C4507RE+ and two Supervisor SUP7L-E (Primary Supervisor in the Slot 3, and the Standby Supervidor in the Slot4). And I have these question: I can connect 04 GLC-SX-MMD in the uplink ports of Supervisor Engine 7L-E (Primary)?. I would like connect 04 3750 switchs in mode 802.1Q. Thanks

ricardorojas123 · ‎08-09-2013

Hi, I have a CCMEv8 and a CUCMv8 connected via VPN site to site, the voice call are working, from the Cisco phones registered in the CCME to phones registered in the CUCM and vice versa. Now I am trying a video call, but the call is established only via audio, the video session is not established. The CCME is added in the CUCM as H.323 Gateway, and the CCME has configured a dial-peer to CUCM. All traffic is permitted in the tunnel VPN. How I can resolve this problem ? Thanks

ricardorojas123 · ‎07-22-2013

Scott, dot11 syslog dot11 ssid SSID1 authentication open authentication key-management wpa wpa-psk ascii 7 dot11 ssid SSID2 authentication open authentication key-management wpa wpa-psk ascii 7 crypto pki token default removal timeout 0 bridge irb interface Dot11Radio0 no ip address encryption mode ciphers tkip ssid SSID1 ssid SSID2 antenna gain 0 channel 2412 station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding interface Dot11Radio1 no ip address encryption mode ciphers tkip ssid SSID1 ssid SSID2 antenna gain 0 dfs band 3 block channel dfs station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding interface GigabitEthernet0 no ip address duplex auto speed auto no keepalive bridge-group 1 bridge-group 1 spanning-disabled no bridge-group 1 source-learning interface BVI1 ip address 10.x.x.y 255.255.255.0 ip default-gateway 10.x.x.y ip forward-protocol nd ip http server no ip http secure-server

ricardorojas123 · ‎07-22-2013

Hi friends, The configuration of the APs was tested in a lab environment and this tests were successful. The AP configuration has two SSID, with WPA v1 and TKIP.

ricardorojas123 · ‎07-22-2013

Hi, I have a Cisco Access Point 1140 Series, and the users has problem when they try connect to the Wireless. In the console I have these messages: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station MAC Reason: Previous authentication no longer valid %DOT11-6-ASSOC: Interface Dot11Radio0, Station MAC Reassociated KEY_MGMT[WPA PSK] %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station MAC Reason: Previous authentication no longer valid %DOT11-6-ASSOC: Interface Dot11Radio0, Station MAC Reassociated KEY_MGMT[WPA PSK] %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station MAC Reason: Previous authentication no longer valid %DOT11-6-ASSOC: Interface Dot11Radio0, Station MAC Reassociated KEY_MGMT[WPA PSK] How I can solve this problem?

ricardorojas123 · ‎06-17-2013

Chris, I have disabled the MTP option, and now the calls can be transfered, thanks!

ricardorojas123 · ‎06-17-2013

I have a CUCMv8.0 and a Gateway 2901, this Router is configured as H.323 Gateway and it has 4 analog lines connected in the fxo ports. The calls received in the fxo ports are transfered to a Cisco phone 7942, the call is process correctly, but when I try to transfer the call to another internal phone, the transfer buttom don´t work. When I call to Cisco phone 7942, from a internal phone, the call is established,and the 7942 can transfer the call to another internal phone without problems. In summary: Incoming Call from the PSTN (FXO) can´t be transfered. Incoming Call from another internal phone (Registered in the same CUCM) can be transfered. Parameters of the Voice Gateway H.323 Gateway Device Protocol: H.225 Media Resource List: MRL Media Termination Point Requered I hope you can help me.

ricardorojas123 · ‎06-17-2013

I reset the phone to factory default, and now the phone is registered in the CUCM.

ricardorojas123 · ‎06-13-2013

Hi In the section: Device > Device Setting > Device Default, in the 6921 I have this: Load Information: SCCP69xx.9-0-3-0 In the section: Software Upgrade / TFTP File Managment, I have these files: BOOT69xx.0-0-0-14.zz.sgn DSP69xx.0-0-0-3.zz.sgn SCCP69xx.9-0-2-0.loads SCCP69xx.9-0-2-0.zz.sgn SCCP69xx.9-0-3-0.loads SCCP69xx.9-0-3-0.zz.sgn

ricardorojas123 · ‎06-13-2013

Hi Jaime, The phones were configured manually in the CUCM, the Cisco 6921 is available in the menu: Device > Phone > Add New > Phone Type: 6921.

ricardorojas123 · ‎06-13-2013

Hi, I'm installing the phone, but the phone does not load its configuration. The handsfree button remains green, and keeps the viewer cisco logo and the phone obtains its IP address from the DHCP server. In the same site I have 7942 Cisco Phone, and all these phones gets their configuration from the CallManager. Additional information: CUCM version: 8.0.3.20000-2 Device Default: SCCP69xx.9-0-3-0 I appreciate your help.

ricardorojas123 · ‎06-05-2013

Hi Jatin, I have uploaded the IOS to c3560-ipbase-mz.122-35.SE5, and now the guest vlan is working. Thank you very much for your help Now I will start to work with Cisco 2960 LAN Lite.

Date Registered	‎03-30-2007 08:30 AM
Date Last Visited	‎08-18-2017 04:01 AM
Total Messages Posted	628

Uplinks SUP7L-E

Uplinks SUP7L-E

Uplinks SUP7L-E

Uplinks SUP7L-E

VideoCall between CUCM and CCME

Constant disconnection of Wireless Clie...

Constant disconnection of Wireless Clie...

Constant disconnection of Wireless Clie...

Transfer external calls to internal pho...

Transfer external calls to internal pho...

Registering 6921 in CUCM 8.0

Registering 6921 in CUCM 8.0

Registering 6921 in CUCM 8.0

Registering 6921 in CUCM 8.0

Guest Vlan - Assignment Error 3560