About franckehret

franckehret · 04-18-2020

Hi all, I've a problem with 5Ghz max data rate in a Mobility Express environement. Issue is the same with my 2x2802i and my 2702i access points (see capture of one - 5Ghz speed is the same on all APs) I can't figure out if this was a release issue u...

franckehret · 04-02-2020

Dear all, In order to get more control on my physical ports, I'm starting to try out 802.1x with a NPS server.I followed instructions from here https://www.youtube.com/watch?v=NIzxpHNtr7I(Of course, not the ISE part) I've setup:- the NPS server polic...

franckehret · 07-11-2019

Hi there, Since a couple of months (no real need the first I've seen this issue), I've noticed I could not connect to my Aironet 2702i in HTTPS.It either shows on Chrome the NET::ERR_CERT_AUTHORITY_INVALID error in a loop mode (I can't continue to th...

franckehret · 02-13-2018

Dear all, I'm a bit stuck with a small environment setup. My current setup is a single 2702i in autonomous mode. The productive SSID is in 5GHz only and the security is WPA2 Enterprise with NPS authentication. My "test" notebook" is a Macbook pro...

franckehret · 09-21-2015

Hello there, Would it be any specific reason why SG500 switch would not accept a proper Cisco SFP copper module (GLC-T). The only log line that I can see is : %NSFP-I-SFPGibicDetected: gi1/27 SFP port is present But even if there is apparently ...

franckehret · 04-22-2020

Hi everyone,First, thanks to all that participated to this quest, I've learned again a lot! :-)So, here are my last findings:- 160Mhz is definitivelly not praticable, unless you have an isolated (or several) AP, with no surroundings). I've opted for ...

franckehret · 04-21-2020

Hi again, So here are my new findings :- I figured out in the doc that radio has to be disabled if you want to change the channel width in RF optimization. That is probably the reason why it shut them off.- Despite having radio cut, it is impossible ...

franckehret · 04-20-2020

Hi again,Thanks for the reply but I've tried that "already". I've tried to change the DCA channel width value to 40 Mhz (or above) but when I click on apply, it gives me the following error : And as a consequence after applying, it reverts the change...

franckehret · 04-19-2020

Same for me, I've noticed it with the very latest version (jumped from 1.4.10.6 to 1.4.11.4)Pretty anoying for me as I generated SSL certificates for FQDNs only... I hope this will (can) be fixed since the vulnerability ;-)

franckehret · 04-02-2020

Never mind, everything was right in the configuration (GPO, switch, etc...).The ONLY missing part was to put the Wired AutoConfig service in automatic mode in Windows... ;-)

Member Since	‎04-11-2014 04:34 AM
Date Last Visited	‎05-06-2022 12:04 AM
Posts	18

User Statistics

User Activity

Access points 5Ghz speed issue

Cisco SG500 802.1x - port based authentication not working

HTTPS issue on Aironet 2702i in autonomous mode

Slow file transfert on 2802i but not on 2702i

Cisco SG500 and copper SFP

Re: Access points 5Ghz speed issue

Re: Access points 5Ghz speed issue

Re: Access points 5Ghz speed issue

Re: SG300-28P Web interface not working with hostname, only with IP, after latest firmware update

Re: Cisco SG500 802.1x - port based authentication not working