About etmarcof

etmarcof · 03-13-2023

I have one CUCM Cluster distributed between two datacenter´s . Some Webex App users on LAN are primarily registered to CUCM-SUB1A in DC-A and register to CUCM-SUB1B in DC-B if DC-A Fails .Others Webex App users are registered primary in DC-B in CUCM-...

etmarcof · 09-15-2022

Hi need to copy one CUCM Virtual Machine (thick disk ) from one Hyperflex 4.5.2b cluster to another Cluster Managed by the same Vcenter 7.0 So i went to one datastore a copy all the files to the other datastore location. But at destination side w...

etmarcof · 02-11-2022

Hi,I have installed one hyperflex cluster but by mistake i used duplicated Mac Prefix during installation and so i need to change them. Do i need to reiinstall hyperflex cluster from scratch or how its possible change MAC Pool on UCSM.? Regards,MC

etmarcof · 02-03-2022

Hi,I have installed one hypeflex cluster 4.0.2 with FI 6454 (Clean Install) and on UCS Manager i noticed that on QoS System Classes all priorities (Platinum,Gold, Silver, Bronze,Best Effort) had MTU set to 9216. In Cisco documentation i saw ...

etmarcof · 10-06-2021

Hi,I have one CUBE with IOS XE 16.12.5 with one SIP Trunk to PSTN with Redundant links.When primary link goes down only incoming calls from PSTN are failing because CUBE as soon receives INVITE reply with SIP/2.0 488 Not Acceptable Media.I have disc...

etmarcof · 10-28-2024

Hi @Meddane , In your post you say that "This COP file enables the “utils system upgrade dataexport initiate” command in Unity Connection 10.c, 11.x and 12.x for migrations to 15." Where do you saw this information? In readme of cop file ciscocm.cu...

etmarcof · 10-28-2024

@Remington , Didn't you received the following error when you installed on 10.5? It seems it install but i'm afraid of the impact of running the data export if not compatible... 10/28/2024 07:29:07 Validating version compatability.10/28/2024 07:29:0...

etmarcof · 10-28-2024

Hi, Anyone have tried to export from CUC 11.0 ? I know that in readme it says Important Note: This cop is installable for source releases 11.5.x, 12.0.x to pre 12.5SU5 and 14FCS. But some lines below it also says on instalation instructions th...

etmarcof · 10-04-2024

Hi, I had the same issue, cop file installation through CLI failed in CUCM 11.0.1. Did you manage to solve the issue? By the logs below it seems that in my case i don't need the cop but I didn't have opportunity yet to run PCD to see if will be ab...

etmarcof · 03-14-2023

Hi @Jonathan Schulenberg , thank you for the inputs! Just to check if i understood the suggestion is two have one expressway-c and expressway-e cluster per DC. But with one single Voice Service Domain or with two subdomains Voice Services Domain...

Member Since	‎08-08-2003 12:47 AM
Date Last Visited	‎03-18-2025 02:34 AM
Posts	377
Total Helpful Votes Received	25

User Statistics

User Activity

Webex App (Unified CM) - MRA workload and redundancy questions

Hyperflex With ESXi thick to thin conversion

Hyperflex - How to change MAC Pool

Hyperflex UCS QoS System Classes MTU parameter setting

Incoming Dial-peer match - SIP/2.0 488 Not Acceptable Media

Re: Upgrade Unity Connection 12.5 to 15 using Fresh Install Data Impor

Re: Unity 11.5 data export COP

Re: Unity 11.5 data export COP

Re: CSCwi52160 - Fresh Install w/ Data import to version 15 COP file F

Re: Webex App (Unified CM) - MRA workload and redundancy questions