hi, C2801-ADVIPSERVICESK9-M), Version 15.0(1)M9 PID: PVDM2-16   when I reload the router I get this message something about firmware for the dsps not sure what to do about it.   RTR#sh voice dsp edsp 0001 01 g729r8 p  0.1 IDLE  50/0/11.1 edsp 0002 02 g729r8 p  0.1 IDLE  50/0/11.2 edsp 0003 01 g729r8 p  0.1 IDLE  50/0/12.1 edsp 0004 02 g729r8 p  0.1 IDLE  50/0/12.2 edsp 0005 01 g729r8 p  0.1 IDLE  50/0/13.1 edsp 0006 02 g729r8 p  0.1 IDLE  50/0/13.2 edsp 0007 01 g729r8 p  0.1 IDLE  50/0/75.1 edsp 0008 01 g729r8 p  0.1 IDLE  50/0/76.1 ----------------------------FLEX VOICE CARD 0 ----------------------- -------                            *DSP VOICE CHANNELS* CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending LEGEND     : (bad)bad    (shut)shutdown  (dpend)download pending DSP    DSP                 DSPWARE CURR  BOOT                         PAK   TX/RX TYPE   NUM CH CODEC        VERSION STATE STATE   RST AI VOICEPORT TS ABRT PACK COUNT ====== === == ========= ========== ===== ======= === == ========= == ==== ============                            *DSP SIGNALING CHANNELS* DSP    DSP                 DSPWARE CURR  BOOT                         PAK   TX/RX TYPE   NUM CH CODEC        VERSION STATE STATE   RST AI VOICEPORT TS ABRT PACK COUNT ====== === == ========= ========== ===== ======= === == ========= == ==== ============ C5510  001 01 {flex}       26.3.12 alloc idle      0  0 0/0/0     02    0         37/0 C5510  001 02 {flex}       26.3.12 alloc idle      0  0 0/0/1     06    0         37/0 C5510  001 03 {flex}       26.3.12 alloc idle      0  0 0/0/2     10    0         37/0 C5510  001 04 {flex}       26.3.12 alloc idle      0  0 0/0/3     14    0         37/0 ------------------------END OF FLEX VOICE CARD 0 ----------------------------   it all seems fine to me but I don't understand why the router is giving that message and if I should do something about it.   this is happening because I updated the IOS to the above version.   I thought I had nothing to do to update the dsp firmware that it was integrated in the ios.     any thoughts?   thanks.   ... View more

hi, ios: Version 12.4(24)T8 cme: 7.1 VIC2-2FXS   I have an analog phone under voice-port 0/2/1 all works fine except sometimes when I call home from outside or when I try to use the phone from inside it doesn't work I have to do a shut and no shut of the interface. when it doesn't work this is what I've been able to find, #sh voice dsp ----------------------------FLEX VOICE CARD 0 ------------------------------                            *DSP VOICE CHANNELS* CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending LEGEND     : (bad)bad    (shut)shutdown  (dpend)download pending DSP   DSP                 DSPWARE CURR  BOOT                         PAK   TX/RX TYPE  NUM CH CODEC        VERSION STATE STATE   RST AI VOICEPORT TS ABRT PACK COUNT ===== === == ========= ========== ===== ======= === == ========= == ==== ============ C5510 001 01 g711ulaw      24.3.8 busy  idle      0  0 0/2/1     01    0     75867/26                            *DSP SIGNALING CHANNELS* DSP   DSP                 DSPWARE CURR  BOOT                         PAK   TX/RX TYPE  NUM CH CODEC        VERSION STATE STATE   RST AI VOICEPORT TS ABRT PACK COUNT ===== === == ========= ========== ===== ======= === == ========= == ==== ============ C5510 001 01 {flex}        24.3.8 alloc idle      0  0 0/0/0     02    0         43/0 C5510 001 02 {flex}        24.3.8 alloc idle      0  0 0/0/1     06    0         36/0 C5510 001 03 {flex}        24.3.8 alloc idle      0  0 0/2/0     02    0         33/0 C5510 001 04 {flex}        24.3.8 alloc idle      0  0 0/2/1     02    0        766/0 ------------------------END OF FLEX VOICE CARD 0 ----------------------------       RTR#sh voice call summary PORT           CODEC     VAD VTSP STATE            VPM STATE ============== ========= === ==================== ====================== 0/0/0         -          -  -                     FXOLS_ONHOOK 0/0/1         -          -  -                     FXOLS_ONHOOK 0/2/0         -          -  -                     FXSLS_ONHOOK 0/2/1         g711ulaw   n  S_SETUP_REQ_PROC      FXSLS_WAIT_OFFHOOK     the phone is not being used but it's s if it's hung the fxs card does not detect that the phone is not being used or something.     voice-port 0/2/1  mwi  cptone CA  timeouts ringing infinity  description *** HOME PHONE ***  station-id name HOMEPHONE  station-id number 41250  caller-id enable     not sure if this is a bug or what. this happens maybe once every 2...3..4 weeks so it doesn't happen every day.     you think moving to IOS 15.0.1M8 will fix this? anyone else had the issue?   I could try to change the phone to the other FXS port but really worth it since this happens every 2...3..4 weeks.   ideas?   thanks.         ... View more

                   hi, I have this 5520 and a router. the asa is a vpn endpoit so let's assume 10 vpns terminate there so the asa has 10 different static routes due to the vpn. I want to advertise these 10 routes into my core router instead of putting manual static entries in my core. so asa has 10 x 10.50.0.0/24 subnets so let's say 10.50.0.0, 10.50.1.0, 10.50.2.0 and so on. this is my config in the asa, access-list EIGRP-DISTRIBUTE-LIST-IN standard deny any access-list EIGRP-DISTRIBUTE-LIST-OUT standard permit 10.50.0.0 255.255.0.0 access-list EIGRP-DISTRIBUTE-LIST-OUT standard deny any router eigrp 77 no auto-summary distribute-list EIGRP-DISTRIBUTE-LIST-OUT out interface inside distribute-list EIGRP-DISTRIBUTE-LIST-IN in interface inside network 10.50.0.0 255.255.0.0 network 10.100.100. 255.255.255.0 passive-interface default redistribute static so basically I want to send the spoke vpn subnets into my core router. I want no routes from the core. so when I do on the core, show ip route eigrp 77 I only see 1 route to 10.50.0.0/16 but yet I say to the asa not to summeraize. this is my config in my core, access-list 77 deny   any router eigrp 77 distribute-list 77 out GigabitEthernet0/0/1 network 10.0.0.0 passive-interface default no passive-interface GigabitEthernet0/0/1 thanks for any help. ... View more

hi, I've configured freeradius as such and I know it works. asa version is Version 9.1(3)                 FREERAD CONFIG   client myasa {         ipaddr = <ipofasa>         netmask = 24         secret = cisco123         nastype = cisco } testuser Cleartext-Password := "testuser"   Service-Type = NAS-Prompt-User from the ASA myasa # test aaa-server authentication FREERAD Server IP Address or name: 10.80.250.13 Username: testuser Password: ******** INFO: Attempting Authentication test to IP address <10.80.250.13> (timeout: 10 seconds) INFO: Authentication Successful interesting ASA config, aaa-server FREERAD protocol radius aaa-server FREERAD (inside) host 10.80.250.13 timeout 5 key ***** authentication-port 1812 group-policy EZVPN internal group-policy EZVPN attributes dns-server value 10.x.x.x vpn-tunnel-protocol ikev1 split-tunnel-policy tunnelspecified split-tunnel-network-list value EZVPN_splitTunnelAcl default-domain value somedomain.com nem enable tunnel-group EZVPN type remote-access tunnel-group EZVPN general-attributes address-pool EZVPNPOOL authentication-server-group FREERAD default-group-policy EZVPN tunnel-group EZVPN ipsec-attributes ikev1 pre-shared-key ***** anyways the response the ASA gets from the FREERADIUS is, %ASA-6-113005: AAA user authentication Rejected : reason = AAA failure : server = 10.80.250.13 : user = testuser but when I do it using the TEST command it works just fine and I just can't figure out why. thanks for any help. this is what I get from freeradius logs, Thu Jan 30 11:18:49 2014 : Auth: Login incorrect: [testuser/testuser] (from client MYASA port 4317184 cli x.x.x.x) ... View more

hi, have a 2801 with 1 4 ports fxo card. let,s say I have 4 1FL lines. 3 of them are cascade and 1 line is a reserved line DID for a store owner. the first 3 are in a trunk group 1 and I have this, voice-port 0/0/0 trunk-group 1 connection plar opx 299 caller-id enable ! voice-port 0/0/1 trunk-group 1 connection plar opx 299 caller-id enable ! voice-port 0/0/3 trunk-group 1 connection plar opx 299 caller-id enable ! voice-port 0/0/4 connection plar opx 212 caller-id enable --> so 299 is my auto attendant and 212 is my own extension. dial-peer voice 1000 pots description *** OUTGOING CALLS *** translation-profile outgoing OUTGOING trunk-group 1 preference 1 destination-pattern .T forward-digits all                    so any calls going outside I want them to use 1 of the 3 lines. what I want to do when calling from my 212 extension outside is to tell the cme use port 4. so port 4 is a did reserved for my phone 212. I don't want phone 212 to use one of the trunk-group lines. how would I do that? thank you!! ... View more

hi, anyone kind enough to provide a sample working configuration of multiple fxo ports (each being a pstn line) and I assuming the telco is doing hunting... so let's say 4 lines, if line 1 is busy the call is sent by the telco on line 2 and so on... incoming and outgoing. thank you very much!!                   I did google it and can't find anything with multiple fxo ports. ... View more