Having SP skills (IOS-XR etc) widens the scope of technical knowledge plus you get the added benefit of being a double CCIE. If you are planning on your first, then R&S covers the core technologies and other CCIE's add on to it. ... View more

Wrong place for the question. Probably why you are not getting any response. Pelase post here: https://learningnetwork.cisco.com/community/certifications?view=discussions ... View more

You are hitting : CSCtd22110    Need support for static multicast MAC entries on Nexus 5000 Nexus 5000/5500 does not support adding static Multicast MAC addresses in valid IGMP range(0100.xxxx.xxxx). For non-IGMP groups, static Multicast MAC can be configured. Example: 5548-2# conf Enter configuration commands, one per line.  End with CNTL/Z. 5548-2(config)# mac address-table static 0300.5e01.2345 vlan 5 interface Ethernet1/14 5548-2(config)# Workaround: If static Multicast MAC needs to be added for valid IP IGMP MAC range, configure static-group using corresponding layer 3 multicast IP address for the multicast MAC in question. Example, for IGMP MAC 0100.5E01.0064, configure 5548-2(config)# vlan x 5548-2(config-vlan)# ip igmp snooping static-group 229.1.0.100 interface x ... View more

Hey Nelson, Traffic has to go through only 1 SCE for being classified correctly, hence the reason for keeping a second will be if you are reaching the max capacity. There is no performance enhancement keeping a 2nd SCE when the one you have is far below it's performance envelope. Shelley. ... View more

Is Multistage classification enabled or disabled? Try flipping that switch. You can find that in Configuration -> Policies -? System Settings -> Advance Options -> Advance options -> Multistage Clasification. It is important to know what Skype is being classified as. Did the TAC engineer that worked with you capture TUR's to understand this issue better? Shelley. ... View more

I verified that in PP25 the supported skype version is 5.3. At this time they have a new version out 5.5. This is ofcourse not supported at this time. Did you test PP25 with 5.3 or lower versions? Refer to this link: http://www.cisco.com/en/US/docs/cable/serv_exch/serv_control/broadband_app/protocol_pack/PP_Note_current.html Shelley. ... View more

Yes, That is why I responded with the words "short answer". I have been troubleshooting SCE for over 5 years now. It all depends on the OS and the protocol pack you are using. And this kind of stuff quickly turns nasty (as in from troubleshooting perspective). What OS and PP are you on? What P2P App is not being throttled? Skype is definatly working in the latest protocol pack as I have not seen any other customers complain but I do not mean to say it is not a new issue. You can answer these questions but because this can lead in to a full blown troubleshooting issue, I suggest you open a TAC case. Shelley. ... View more

Short answer is yes. Shelley. ... View more

Again not sure wihch package we are targetting but I fixed both that had reditection in it. Here is what it should look like. Shelley. ... View more

The only place I see block and redirect is the Default package and I done see any other service allowed. You need to allow the redirection url as a special service. I see it created but take it out an allow it here in this package. *.dealer.e.net.kw:/* *.knetpay.com.kw:/* *.madacare.com.kw:/* These URL's are not in the Flavor you defined. put all of them in and allow them. the other package which had redirection attached to it, I see the redirection url specified but not all allowed url's are in that flavor. what is your exit strategy once the user hits the redirection site? at this time it seems like anything the user does you are redirecting him and it will alway be redirected with no exit clause. You will see the "until subscriber browses to" you need to use this to kill the redirection loop and let the customer come out of the redirection gracefully. ... View more

Attach the PQB here for me to see the policy. There is something wrong with it. If you dont feel comfortable making your SCE policy public please open a TAC case and we will work with you to fix this issue. Shelley. ... View more

First thoughts: You possibly are in a redirection loop.  You are redirecting to a webpage that is blocked and that in turn causes another redirection and it goes on and on and on. Create a flavor with the redirection site and put in a separate service. Then all the service in the package if that is not already done. Shelley. ... View more

Was this working before? The error suggests that the INI_VALUES table was not found on the CM and hence cannot connect. Can you retrieve config from the SCE on the SCA-BB and reapply. Ensure that it also updates the CM on the logs below in the SCA-BB. The INI_Values tables should form by itself. If not you may have to go to the CM and see if the INI_VALUES table exists and if it does you will delete it and try the steps above again. Shelley. ... View more

HSRP requires a L3 card and 5010 does not support a L3 card. Hence this is not a supported config. HSRP is not supported on a 5010. You can conifgure it but the kepalives will not work hence both sides will be active. Shelley. ... View more