Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Ally Moghimian
Stats
Member since
07-16-2013
9
Posts
0
Helpful
0
Solutions
Created by
Ally Moghimian
in Network Management
in Network Management
09-04-2015
05:13 AM
09-04-2015
05:13 AM
Hi, We have more than 60 switches and routers, with lots of different configurations. is there a Windows-based app/solution that allows administrator to automatically backup the current configuration (with/without version management) on a schedule? Regards, Ally
... View more
Labels:
Created by
Ally Moghimian
in IP Telephony and Phones
in IP Telephony and Phones
06-20-2014
02:21 AM
06-20-2014
02:21 AM
that's very true!!! thanks for getting in touch anyway cheers, Ally
... View more
Created by
Ally Moghimian
in IP Telephony and Phones
in IP Telephony and Phones
06-20-2014
02:17 AM
06-20-2014
02:17 AM
Hi, we migrated DHCP records like-for-like. so there wasn't any need to modify the server apart from unauthorizing the old one and authorizing the new one. However, spent some time on our gateway switch and discovered that IP helper for the voice vlan was pointing to the old DHCP server, hence the failure of relaying requests to the new server. changed the IP helper IP address and everything seems to be working as normal. regards, Ally
... View more
Created by
Ally Moghimian
in IP Telephony and Phones
in IP Telephony and Phones
06-20-2014
12:45 AM
06-20-2014
12:45 AM
Hi, We have few Cisco 6921 phones currently registered with our CUCUM BE3000. We have migrated to a new AD DHCP server, but having problem with phones that are switched off and back on again. they don't simply register with the new DHCP server. CUCUM can ping and communicate to DHCP server, but phones that are restarted, have no luck. The phones there were left switched on, are working properly. any idea what else needs to be changed/tested? many thanks, Ally
... View more
Labels:
10-30-2013
01:32 AM
Andrew, thanks for your reply. That's pretty much what I had in mind. As you mentioned, it's for adding to the existing port capacity and should be relatively simple. cheers, Ally
... View more
10-28-2013
02:23 PM
Hi, Got a new 24port 2960 switch to add to our existing infrastructure. Not sure where to start from. Would copying from the existing config on couple of other switches be an option? Or does it have to be from scratch, beside giving a new address, etc? Thanks.
... View more
Labels:
Created by
Ally Moghimian
in Wireless and Mobility
in Wireless and Mobility
07-17-2013
03:46 AM
07-17-2013
03:46 AM
I managed to figure it out! I used your hint and checked out the WEP key. The Hex was encrypted and client settings were set to No-Encryption. I changed the keys and all seems fine. Thanks you all for the advice and the impressive response time!!
... View more
Created by
Ally Moghimian
in Wireless and Mobility
in Wireless and Mobility
07-16-2013
02:28 PM
07-16-2013
02:28 PM
The WEP key is fine, as the client connects (seems like it) to the device, I get full 5 bars on client's screen. having said that, the client fails to ping the AP. On AP's GUI, I can see the client is associated but the IP is 0.0.0.0 Will upload the config here later on. thanks.
... View more
Created by
Ally Moghimian
in Wireless and Mobility
in Wireless and Mobility
07-16-2013
02:02 PM
07-16-2013
02:02 PM
Hi, Got a brand new Aironet 1602e out of the box. It got it IP address from the DHCP address including the subnet and gateway. enabled dot11.0, set to throughput and assigned a wep key. assigned SSID and set it to guest mode. The client device (a barcode scanner) connect to the AP without any problem, but it doesn't receive an IP from Windows 2003's DHCP pool. There is no Wireless controller used in the infrastructure and other AP points (older 1200) are configured the same way and they are all fine. Is there any traffic being filtered out on this newer model? the configs are the same as the older APs but still clients do not connect to/see DHCP server. any help is much appreciated.
... View more
Labels:
09-04-2015
Hi,We have more than 60 switches and routers, with lots of different
configurations.is there a Windo...
06-20-2014
Hi,we migrated DHCP records like-for-like. so there wasn't any need to
modify the server apart from ...
Created by
Ally Moghimian
in IP Telephony and Phones
06-20-2014
06-20-2014
Hi,We have few Cisco 6921 phones currently registered with our CUCUM
BE3000.We have migrated to a ne...
10-30-2013
Andrew,thanks for your reply.That's pretty much what I had in mind. As
you mentioned, it's for addin...
10-28-2013
Hi,Got a new 24port 2960 switch to add to our existing
infrastructure.Not sure where to start from. ...
Created by
Ally Moghimian
in Wireless and Mobility
07-17-2013
07-17-2013
I managed to figure it out!I used your hint and checked out the WEP key.
The Hex was encrypted and c...
Created by
Ally Moghimian
in Wireless and Mobility
07-16-2013
07-16-2013
The WEP key is fine, as the client connects (seems like it) to the
device, I get full 5 bars on clie...
Public Statistics
| Date Registered | 07-16-2013 09:52 AM |
| Date Last Visited | 08-18-2017 04:27 AM |
| Total Messages Posted | 9 |
