Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Ninad Thakare
12-26-2017
Stats
Member since
10-16-2013
61
Posts
5
Helpful
0
Solutions
12-17-2017
05:27 AM
Hi Marvin,
I have set Intrusion Policy to "Balanced security and connectivity" and logging with "Log at end connection" for Allow traffic and "log at beginning of connection".
... View more
12-16-2017
09:00 AM
Hi,
Yes, thought so but with NTP or manual setup still no success. I am not getting any data on dashboard.
... View more
12-16-2017
01:57 AM
I have installed FMC and registered 2 SFR module successful.
I have also configured ASA to send traffic to SFR for traffic analysis but still I am not able to see any traffic on FMC being analyzed.
Below is the ASA config :
ASA/act# show service-policy sfr
Global policy: Service-policy: global_policy Class-map: global-class-sfr SFR: card status Up, mode fail-open packet input 3769932114, packet output 3770123526, drop 96788, reset-drop 0 ASA/act#
... View more
- Tags:
- asa
- fmc
- sfr
- sfr module
Labels:
10-24-2017
05:36 AM
Hi All,
I was having one ASA 5525X with IPS module (which we never used).
Then we purchased new ASA 5525X with SFR module to deploy SFR in our environment.
The situation is :
We have ASA with SFR is active and I am trying to add ASA with IPS in an HA.
As the hardware is mismatching, I am not able to configure it in HA.
I tried, shutting IPS down and also uninstall IPS module. Still I am not able to configure it in HA.
What will be the solution for this? Can I remove IPS ?
... View more
Labels:
05-30-2017
05:03 AM
Hi Team,
I have Cisco ASA and earlier it was having local users without AAA enabled. So we have admin users and few Read-only user.
Now I have configured AAA with Radius server on it. And my users are added on Radius server to authenticate.
Issue is all my users are getting admin privilege, for those who earlier has privilege level 5 too.
How can I sort out read-only user in this situation.
Thanks in advance.
Regards,
Ninad Thakare
... View more
Labels:
11-19-2014
11:42 PM
Hi Rasika, Its an new installation and working on isolated network not on production. where as we dont have NTP server and not able to configure time on WLC. But we have matched same time with AP and WLC. Attached file consist of required info. Regards, Ninad
... View more
11-19-2014
08:29 PM
Hi Leo, Thanks for the reply. Actually we are facing the AP registration with WLC showing an error which is enclosed in an attachment even though the AP is getting the DHCP IP from WLC and also able to ping. Hence we thought for upgrade the Lightweight AP firmware and then try to register, but we are getting the upgradation process of it. Attachment is FYI.
... View more
Created by
Ninad Thakare
in Wireless and Mobility
in Wireless and Mobility
11-19-2014
06:43 PM
11-19-2014
06:43 PM
Hi Support, Can I get the procedure to upgrade the firmware of leightweight AP 2702i firmware to its latest version of leightweight firmware. All I am getting is the Leightweight to Autonomous procedure which I dont require. Regards, Ninad Thakare
... View more
Labels:
11-02-2014
09:35 PM
Hi Support, I have configured the ASA CX and configured the Web filtering policies. In the policies, I have created the user objects for each of my user with their IP address for the Source. But I need to integrate it with Active Directory which will be easy for me to add user in the object group by their domain username. what will be the steps for it. And also that can be easily identified in the event tab with that username, as for now its just showing me the IP of the user doing illegal surfing. Thanks in advance for the help. Regards, Ninad thakare
... View more
Labels:
Created by
Ninad Thakare
in Other Security Subjects
in Other Security Subjects
08-31-2014
10:16 PM
08-31-2014
10:16 PM
So it will work as : ! object network NETWORK_OBT_10.10.10.0_24 nat (outside,outside) dynamic interface. !
... View more
08-25-2014
04:43 AM
Hi, Saw the Bug report, but I'am still not able enable it. ASA(config)# clear xlate INFO: 732 xlates deleted ASA(config)# crypto ikev1 enable outside ERROR: IkeReceiverInit, unable to bind to port ASA(config)# Can you please help. Regards, Ninad Thakare
... View more
08-24-2014
10:56 PM
I have configured CXSC on ASA5515-X. I need reverse situation. My Teamviewer and Ammyy Admin is not working. Can you help me how I can allow it, because its coming under uncategorize application and illigeal URl content. Regards, Ninad
... View more
08-22-2014
10:36 PM
Do I need to use VPN pool from inside subnet so that it will be considered in : nat (inside,outside) statement
... View more
Created by
Ninad Thakare
in Other Security Subjects
in Other Security Subjects
08-20-2014
08:24 PM
08-20-2014
08:24 PM
Hi, My IPSec Tunnel is UP and able to connect all network. But the VPN client is not able to get Internet. They are not able to access Internet. Note : I have not configured split tunneling. Please help. Brgrds, Ninad Thakare
... View more
12-17-2017
Hi Marvin, I have set Intrusion Policy to "Balanced security and
connectivity" and logging with "Log...
12-16-2017
Hi, Yes, thought so but with NTP or manual setup still no success. I am
not getting any data on dash...
12-16-2017
I have installed FMC and registered 2 SFR module successful. I have also
configured ASA to send traf...
10-24-2017
Hi All, I was having one ASA 5525X with IPS module (which we never
used). Then we purchased new ASA ...
05-30-2017
Hi Team, I have Cisco ASA and earlier it was having local users without
AAA enabled. So we have admi...
11-19-2014
Hi Rasika,Its an new installation and working on isolated network not on
production.where as we dont...
11-19-2014
Hi Leo,Thanks for the reply.Actually we are facing the AP registration
with WLC showing an error whi...
Created by
Ninad Thakare
in Wireless and Mobility
11-19-2014
11-19-2014
Hi Support, Can I get the procedure to upgrade the firmware of
leightweight AP 2702i firmware to its...
11-02-2014
Hi Support,I have configured the ASA CX and configured the Web filtering
policies.In the policies, I...
08-31-2014
So it will work as :! object network NETWORK_OBT_10.10.10.0_24 nat
(outside,outside) dynamic interfa...
08-25-2014
Hi,Saw the Bug report, but I'am still not able enable it.ASA(config)#
clear xlateINFO: 732 xlates de...
08-24-2014
I have configured CXSC on ASA5515-X.I need reverse situation. My
Teamviewer and Ammyy Admin is not w...
08-22-2014
Do I need to use VPN pool from inside subnet so that it will be
considered in :nat (inside,outside) ...
Public Statistics
| Date Registered | 10-16-2013 01:27 AM |
| Date Last Visited | 12-26-2017 11:50 PM |
| Total Messages Posted | 61 |
| Total Helpful Votes Received | 5 |
