Hi NetPro. Currently i doing the IOS patching for Cat4k switch, however i am facing some problem after the switch rebooted . this Cat4k doesn't reload with the new IOS. i have tried 2 times but still can't boot up the new IOS. your reply will be highly appreciated. here with the switch information. Cisco Internetwork Operating System Software IOS (tm) Catalyst 4000 L3 Switch Software (cat4000-I5S-M), Version 12.1(19)EW1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/tac Copyright (c) 1986-2003 by cisco Systems, Inc. Compiled Mon 28-Jul-03 15:48 by eaarmas Image text-base: 0x00000000, data-base: 0x00F12E30 ROM: 12.2(20r)EW1 Dagobah Revision 86, Swamp Revision 29 Switch1 uptime is 2 days, 12 hours, 49 minutes System returned to ROM by reload System restarted at 03:19:08 CCT Tue Mar 2 2010 System image file is "bootflash:" cisco WS-C4507R (XPC8245) processor (revision 7) with 524288K bytes of memory. Processor board ID FOX090402Q1 Last reset from Reload 96 FastEthernet/IEEE 802.3 interface(s) 2 Gigabit Ethernet/IEEE 802.3 interface(s) 403K bytes of non-volatile configuration memory. Configuration register is 0x2101 ************************************************************************* switch#dir Directory of bootflash:/     1  -rw-     9044200   Apr 01 2005 07:16:18  cat4000-i5s-mz.121-19.EW1.bin     2  -rw-    12939640   Jan 21 2010 09:30:26  cat4000-i5k91s-mz.122-25.EWA14.bin *************************************************************************** switch#sh run | in boot boot system flash bootflash:cat4000-i5k91s-mz.122-25.EWA14.bin boot system flash bootflash:cat4000-i5s-mz.121-19.EW1.bin Regards, Jackal ... View more

Hi NetPro. would it be possible if i wanna configure the switch to send alert / alarm while the CPU Utilization hit to 50% - 80% to my monitoring server ? i have check with the monitoring administrator , he was mentioned must give him " MIB " . thus i am wondering where and how can i get this mib file for him ? appreciate your reply . thanks netpro. jack ... View more

Hi NetPro, Does anyone know how to solve this ? My switch 3750 down with this error msg. your reply will be highly appreciated. %TCAMMGR-3-HANDLE_ERROR: cam handle [hex] is invalid The CAM Handle used by the caller is not valid. Recommended Action: Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Also perform a search of the Bug Toolkit http://www.cisco.com/pcgi-bin/Support/Bugtool/home.pl. If you still require assistance, open a case with the Technical Assistance Center via the Internet http://tools.cisco.com/ServiceRequestTool/create, or contact your Cisco technical support representative and provide the representative with the gathered information. Related documents- No specific documents apply to this error message. ... View more

Hi NetPro, i've loaded the VeriSign Cert but somehow i still hitting the major problem. Scenario 1: Company A recommend CN = test-radius-01@google.com VeriSign recommend CN = test-radius-01.google.com but, while in the UAT stage . Cert with "CN = test-radius-01.google.com" working on the Laptop . not in the production level. anyone encountered this before ? thanks a lot Jack ... View more

Hi NetPro, After IOS upgrade , this AP can not Associate anymore. Previous IOS version : flash:/c1240-k9w7-mx.123-7.JA5/c1240-k9w7-mx.123-7.JA5 Proposed IOS Version : c1240-k9w7-tar.124-10b.JDA3.tar AP Model : AIR-AP1242AG-E-K9 Interface IP-Address OK? Method Status Protocol BVI1 10.68.151.15 YES NVRAM up up Dot11Radio0 unassigned YES NVRAM initializing down FastEthernet0 unassigned YES NVRAM up up P/S : Radio keep initializing status . your reply will be highly appreciated. thanks a lot. Jack ... View more

Hi Netpro, Anyone know how to check the IP Address, Mask and Default Gateway in GUI ? because, my Appliance console mode is not working, so i would like to know the alternative way checking the default gateway in GUI base. possible ? your reply will be highly appreciated. thanks a lot. ... View more

Hi Netpro, Anyone know how to check the IP Address, Mask and Default Gateway in GUI ? because, my Appliance console mode is not working, so i would like to know the alternative way checking the default gateway in GUI base. possible ? your reply will be highly appreciated. thanks a lot. ... View more

Hi NetPro, i would like to know about the Switch / Router . if the IOS image initially using IPBASE, (flash:c2800nm-ipbasek9-mz.124-3e.bin) , i plan to upgrade to c2800nm-entbasek9-mz.124-24.T1.bin . will this causing problem or the hardware is not compatible to this ios image ? your reply will be highly appreciated. regards, Jack ... View more