About Carlomd

Carlomd · 05-05-2025

Hello all,I have a C9105axi-b, which I know after reading around can be converted as a EWC ap, I followed a couple of youtube videos, I also did the day 0 setup, but somehow for the life of me, I can't reach or ping the INT0 of the AP, I'm coming fro...

Carlomd · 03-25-2021

Hi all, I downloaded the free ver of DAG and installed it on my 2019 Server, so we’re trying to get a test run for a pilot group of users, we have AD, I have the DAG setup and connected to AD, I’m reading on the docs it mentioned the next step is to ...

Carlomd · 03-22-2021

Hi all, I have a windows 2019 server installed with DAG, I’m using the basic setting for AD integration, I’m not using ldaps, just ldap, and somehow it won’t connect to ldap, it gets an error “LDAP connect failed” whenever I try to save the settings,...

Carlomd · 01-29-2021

Hi all,We went through a network redesign with our consultant, were undergoing a cyber security compliance checklist, we have a pair of n9k's in vpc, some older catalyst switches, one of them a c4948 still has the stp root according to our consultant...

Carlomd · 09-04-2020

Hi all,We have a project to redesign our core switches, this is my first time setting up vpc on 2 n9k 9372tx and wanted to get some pointers on which is a good direction, I've searched around, I know everyone has a different setup on their networks s...

Carlomd · 05-06-2025

Thanks, I'm reevaluating my setup and may just stick with Aruba's, since these 9105's are EOL, and looks like only if you run them using a separate controller they will continue to be supported and also the licensing can be a pain, may not be cost ef...

Carlomd · 05-06-2025

Yeah it's the same after trying some of the commands, I had it where it was pinging ok on the same subnet, except its own, and pinging from across other subnets didn't work. But now it just reverted back to not pinging any ip at all. Thanks for the g...

Carlomd · 05-05-2025

I did reload after wr mem, for some strange reason it keeps putting back the default route after issuing a no ip route 0.0.0.0 0.0.0.0 GigabitEthernet0 250it would be there again after reloading, so I have a catalyst 9200 sw and I read I'm supposed t...

Carlomd · 05-05-2025

Rich, thanks for the detailed pointers, gotcha on the gig 0 rather than int0 so I followed your commands to remove the default route no route 0.0.0.0 0.0.0.0 GigabitEthernet0 250instead with ip route 0.0.0.0 0.0.0.0 GigabitEthernet0 172.16.xx.x (my g...

Carlomd · 05-05-2025

Marce,that is the output from my switch above.

Member Since	‎10-21-2001 11:45 AM
Date Last Visited	‎05-09-2025 02:31 AM
Posts	149
Total Helpful Votes Received	6

User Statistics

User Activity

C9105AXIU-B int0 not pingable on subnet, webui not accessible

Getting on premise for Windows Dag running

First time setting up DAG with AD integration

Move stp root to vpc n9k

New core design

Re: C9105AXIU-B int0 not pingable on subnet, webui not accessible

Re: C9105AXIU-B int0 not pingable on subnet, webui not accessible

Re: C9105AXIU-B int0 not pingable on subnet, webui not accessible

Re: C9105AXIU-B int0 not pingable on subnet, webui not accessible

Re: C9105AXIU-B int0 not pingable on subnet, webui not accessible