Cisco Community
English
Register
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
K@yT
‎02-14-2021
Beginner
Personal Website
Recent Badges
Awards
Recent Badges
See all
20 Replies
1 Helpful Vote
1 Accepted Solution
10 Replies
5 Replies
Stats
Member since ‎09-26-2019
24
Posts
5
Helpful
1
Solution
Certifications
Understanding of Cisco Network Devices
CCNA
Cisco Certified Network Associate Routing and Switching (CCNA Routing and Switching)
CCNA
Cisco Certified Network Associate Routing and Switching (CCNA Routing and Switching)
CCNA

Re: 2960X SWITCH NOT BOOTING

Created by in Switching
02-11-2021
02-11-2021
Hi, Barnard!Try to Load iOS in this format c2960x-universalk9-tar.150-2a.EX5.tar

Re: Reset a 2960X correctly

Created by in Switching
09-30-2020
09-30-2020
Here are easy steps:REMOVE POWER CABLE then PLUG it back again. PRESS & HOLD MODE BOTTON for 8 mins....

Re: SMTP Issue

Created by in Other Network Architecture Subjects
09-27-2020
09-27-2020
[Solution]: We had to run network performance assessment from Microsoft team to clean up o365 exchan...

Re: SMTP Issue

Created by in Other Network Architecture Subjects
07-25-2020
07-25-2020
Hi @paul driver Yes, (Local) and but our exchange is not online,hosted externally..Yes, the Dns serv...

Re: NAT trouble with web and smtp

Created by in Other Network Architecture Subjects
07-23-2020
07-23-2020
hi @gold78 can you please mention what worked better? 

Re: failed in sending smtp mail using CiscoWorks

Created by in Other Network Architecture Subjects
07-23-2020
07-23-2020
Hi @samir_issam is your pc on domain if so try to remove it from the domain, check if it works.

SMTP Issue

Created by in Other Network Architecture Subjects
07-23-2020
07-23-2020
Hi Net-Worriers Here is a network nightmare i am confronting, clients have internet access on the PC...

Re: Converting a Switch port to HUB port

Created by in Other Network Architecture Subjects
07-23-2020
07-23-2020
Or try to flush the switch then used it without any configs in it. @rodriguesl

Re: Converting a Switch port to HUB port

Created by in Other Network Architecture Subjects
07-23-2020
07-23-2020
make it a trunk port and see if that's what you looking for...@rodriguesl

Re: Converting a Switch port to HUB port

Created by in Other Network Architecture Subjects
07-23-2020
07-23-2020
Hi, rodrigueslNot sure if i understand your question...however Go to that Port and Configure it as a...

Re: What it is needed to make a Cisco Catalyst 3750G-48PS Switch as a hub?

Created by in Switching
10-31-2019
10-31-2019

Re: Converting a Switch port to HUB port

Created by in Other Network Architecture Subjects
10-31-2019
10-31-2019
Hihere is example of configs you need to go through....Converting a Switch port access to HUB portci...

Re: Converting a Switch port to HUB port

Created by in Other Network Architecture Subjects
10-31-2019
10-31-2019
Yes is possible!

Re: Converting a Switch port to HUB port

Created by in Other Network Architecture Subjects
10-31-2019
10-31-2019
Hi You erase all the configs from the access switch you want to use as an HUB and add Vlan interface...

Re: What it is needed to make a Cisco Catalyst 3750G-48PS Switch as a hub?

Created by in Switching
10-19-2019
10-19-2019
HiI’ll send you our network diagram now and switch configuration on Monday.TY
Public Statistics
Date Registered ‎09-26-2019 03:11 AM
Date Last Visited ‎02-14-2021 03:48 PM
Total Messages Posted 24
Total Helpful Votes Received 5
Helpful Votes Given To
Helpful Votes From
See all >