OUTGOING CALL ROUTING

[cruz.javier]

I have UC560 with E1,

if im try to make a call for default it try FXO trunks. I want to use My E1

dial-peer voice 63 pots

trunkgroup ALL_FXO

corlist outgoing call-national-plus

description **CCA*Mexico*Long Distance Mobile**

translation-profile outgoing OUTGOING_TRANSLATION_PROFILE

preference 5

destination-pattern 9045..........

forward-digits all

no sip-register

voice-port 0/3/0:1

!

voice-port 0/1/0

trunk-group ALL_FXO 64

cptone MX

connection plar opx 30099

description Configured by CCA 4 FXO-0/1/0-OP

caller-id enable

!

voice-port 0/1/1

trunk-group ALL_FXO 64

cptone MX

connection plar opx 30099

description Configured by CCA 4 FXO-0/1/1-OP

caller-id enable

!

voice-port 0/1/2

trunk-group ALL_FXO 64

cptone MX

connection plar opx 30099

description Configured by CCA 4 FXO-0/1/2-OP

caller-id enable

!

voice-port 0/1/3

trunk-group ALL_FXO 64

cptone MX

connection plar opx 30099

description Configured by CCA 4 FXO-0/1/3-OP

caller-id enable

!

controller E1 0/3/0

framing NO-CRC4

line-termination 75-ohm

ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled ani

cas-custom 1

  country telmex

  category 2

  answer-signal group-b 1

  caller-digits 4

  groupa-callerid-end

how can i config alla the outbound calls need to be router to the E1???

[David Trad · Accepted solution]

Hi Cruz,

In CCA did you configure your E-1 correctly?

If you have no need for the FXO ports then in CCA you can disable them so that way all your calls go directly to the E-1 service.

Are you getting any errors when you try to make a call now? Do you have some ISDN debug captures for us to look at?

Cheers,


David Trad.

[cruz.javier]

I did the configurarion in the CLI, becasu for Mexico i dont hace the options in the CCA for R2 Modified, i used this configuration for the E1 port:

controller E1 0/3/0

framing NO-CRC4

line-termination 75-ohm

ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled ani

cas-custom 1

  country telmex

  category 2

  answer-signal group-b 1

  caller-digits 4

  group-callerid-end

I contracted with the ISP the E1 complete 31 channels.

When i made a try to call on the IP phone it take to long to get a tone and the cut off the signal, i call 9 and 7 digits (93149693).

i have this in the default sh run command

trunk group ALL_FXO

max-retry 5

voice-class cause-code 1

hunt-scheme longest-idle

!

voice-port 0/3/0:1

!

voice-port 0/1/0

trunk-group ALL_FXO 64

cptone MX

connection plar opx 30099

description Configured by CCA 4 FXO-0/1/0-OP

caller-id enable

!

voice-port 0/1/1

trunk-group ALL_FXO 64

cptone MX

connection plar opx 30099

description Configured by CCA 4 FXO-0/1/1-OP

caller-id enable

!

voice-port 0/1/2

trunk-group ALL_FXO 64

cptone MX

connection plar opx 30099

description Configured by CCA 4 FXO-0/1/2-OP

caller-id enable

!

voice-port 0/1/3

trunk-group ALL_FXO 64

cptone MX

connection plar opx 30099

description Configured by CCA 4 FXO-0/1/3-OP

caller-id enable

dial-peer voice 59 pots

trunkgroup ALL_FXO

corlist outgoing call-international

description **CCA*Mexico*International Calls**

translation-profile outgoing OUTGOING_TRANSLATION_PROFILE

preference 5

destination-pattern 900T

forward-digits all

no sip-register

!

dial-peer voice 61 pots

trunkgroup ALL_FXO

corlist outgoing call-national

description **CCA*Mexico*LADA**

translation-profile outgoing OUTGOING_TRANSLATION_PROFILE

preference 5

destination-pattern 901..........

forward-digits all

no sip-register

!

dial-peer voice 63 pots

trunkgroup ALL_FXO

corlist outgoing call-national-plus

description **CCA*Mexico*Long Distance Mobile**

translation-profile outgoing OUTGOING_TRANSLATION_PROFILE

preference 5

destination-pattern 9045..........

forward-digits all

no sip-register

!

dial-peer voice 65 pots

trunkgroup ALL_FXO

corlist outgoing call-emergency

description **CCA*Mexico*Emergency**

translation-profile outgoing OUTGOING_TRANSLATION_PROFILE

preference 5

destination-pattern 9060

forward-digits all

no sip-register

!

dial-peer voice 67 pots

trunkgroup ALL_FXO

corlist outgoing call-emergency

description **CCA*Mexico*Emergency**

preference 5

destination-pattern 060

forward-digits all

no sip-register

!

dial-peer voice 69 pots

trunkgroup ALL_FXO

corlist outgoing call-local-plus

description **CCA*Mexico*Local Mobile Numbers**

translation-profile outgoing OUTGOING_TRANSLATION_PROFILE

preference 5

destination-pattern 9044..........

forward-digits all

no sip-register

!

dial-peer voice 71 pots

trunkgroup ALL_FXO

corlist outgoing call-local

description **CCA*Mexico*Local Calls - 7, 8 or 10 digits depending on loca**

translation-profile outgoing OUTGOING_TRANSLATION_PROFILE

preference 5

destination-pattern 9[1-9]T

forward-digits all

no sip-register

The issue here is in the dial peer is directed to trunkgroup ALL_FXO, and this trunkgroup is in the FXO trunks.

I dont know how can i tell to the UC to use the E1 port instead of FXO.

I need help for this.

[David Trad]

Hi Cruz,

Can you please put your configuration onto a text file, and then upload it up too hear so I can see it please.

Please also make sure to remove any of the sensative information such as username and passwords and WAN ip addresses from the configuration, or just replace the characters with an "X" so that way you do not reveal any sensative information.

Cheers,


David Trad.

[cruz.javier]

There it is at my dropbox in text file, im researchin if i found some on the google..

http://dl.dropbox.com/u/37621655/run-uc560-latelec

[David Trad]

Hi Cruz,

Please give the following a try... I hope I havent missed anything as I am at work right now and wasnt able to spend much time on it, but this is all I could come up with right now without focusing on the issue...

In theory you should be able to just copy and paste this as I have tried to steer away from anything that is the same on yoru configuration, however before you apply this configuration please make a backup of your current one.

trunk group ALL_T1E1
 hunt-scheme longest-idle
 translation-profile outgoing PROFILE_ALL_T1E1
voice translation-profile PROFILE_ALL_T1E1
 translate calling 4
voice translation-profile nondialable
 translate called 1000
voice translation-rule 4
 rule 15 /^...$/ //
voice translation-rule 1000
 rule 1 /.*/ //
dial-peer voice 6 pots
 description tcatch all dial peer for BRI/PRIv
 translation-profile incoming nondialable
 incoming called-number .%
 direct-inward-dial
dial-peer voice 59 pots
 trunkgroup ALL_T1E1
 corlist outgoing call-international
 description **CCA*Mexico*International Calls**
 translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
 preference 5
 destination-pattern 900T
 forward-digits all
 no sip-register
!
dial-peer voice 61 pots
 trunkgroup ALL_T1E1
 corlist outgoing call-national
 description **CCA*Mexico*LADA**
 translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
 preference 5
 destination-pattern 901..........
 forward-digits all
 no sip-register
!
dial-peer voice 63 pots
 trunkgroup ALL_T1E1
 corlist outgoing call-national-plus
 description **CCA*Mexico*Long Distance Mobile**
 translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
 preference 5
 destination-pattern 9045..........
 forward-digits all
 no sip-register
!
dial-peer voice 65 pots
 trunkgroup ALL_T1E1
 corlist outgoing call-emergency
 description **CCA*Mexico*Emergency**
 translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
 preference 5
 destination-pattern 9060
 forward-digits all
 no sip-register
!
dial-peer voice 67 pots
 trunkgroup ALL_T1E1
 corlist outgoing call-emergency
 description **CCA*Mexico*Emergency**
 preference 5
 destination-pattern 060
 forward-digits all
 no sip-register
!
dial-peer voice 69 pots
 trunkgroup ALL_T1E1
 corlist outgoing call-local-plus
 description **CCA*Mexico*Local Mobile Numbers**
 translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
 preference 5
 destination-pattern 9044..........
 forward-digits all
 no sip-register
!
dial-peer voice 71 pots
 trunkgroup ALL_T1E1
 corlist outgoing call-local
 description **CCA*Mexico*Local Calls - 7, 8 or 10 digits depending on loca**
 translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
 preference 5
 destination-pattern 9[1-9]T
 forward-digits all
 no sip-register

Good luck and I hope this resolves your issues for you.

Cheers,


David Trad.

[cruz.javier]

I will try tomorrow in the morning in the office.

I have one question where did you tell to use the E1 port, as i see here you create a trunk group for ALL_T1E1 but this name is customized right?

i does not mean the UC will know wich port is for outgoing calls.

For example this

voice-port 0/3/0:1

!

voice-port 0/1/0

trunk-group ALL_FXO 64

cptone MX

connection plar opx 30099

description Configured by CCA 4 FXO-0/1/0-OP

caller-id enable

!

Voice port 0/1/0 is the FXO and member of trunk group ALL_FXO

And i suppones my E1 is the Voice-Port 0/3/0:1

What is the meaning of 0:1, channel 1? or it is the complete channel the first  longest iddle?

How it works?

[David Trad]

Hi Cruz,

I am not sure why yours is that, I mostly see the E1's here in Australia as "voice-port 0/2/0:15"

I couldn't tell you how the E1 should be configured in your country sadly

If you are not sure if the ISDN is working (E1) then make sure you do a "debug isdn q931" and advise of the results.

Cheers,


David Trad.