Provisioning XML file with SPA232D

wendellprincipe · ‎04-12-2013

Hi,

I need some help to figure out what is the correct XML configuration to set the DECT parameters.

SPA232D has 1x PSTN, 1x LINE, 10x DECT connections

My question is how to provision DECT lines?

configuration is something like below...

<Line_Enable_1_ ua="na">No</Line_Enable_1_>

<Proxy_1_ ua="na">111.222.33.44</Proxy_1_>

<Display_Name_1_ ua="na">!USER!</Display_Name_1_>

<User_ID_1_ ua="na">!USER!</User_ID_1_>

<Password_1_ ua="na">!PASSWORD!</Password_1_>

<Use_Auth_ID_1_ ua="na">No</Use_Auth_ID_1_>

<Auth_ID_1_ ua="na">!USER!</Auth_ID_1_>

<Mini_Certificate_1_ ua="na"></Mini_Certificate_1_>

<SRTP_Private_Key_1_ ua="na"></SRTP_Private_Key_1_>

<Line_Enable_2_ ua="na">No</Line_Enable_2_>

...

Tried reading the provisioning guide under Voice parametes page 81, mentioned only for lines but non for DECT.

http://www.cisco.com/en/US/docs/voice_ip_comm/csbpvga/spa100-200/provisioning/guide/SPA100-200_PG_78-20952.pdf

SPA232D

Dan Lukes · ‎04-12-2013

Are you asking about the syntax ? Well, you may read the documentation. Or you may save the configuration from configured device into file (either using /admin/config.xml URL or utilising SIP NOTIFY method) and use it as example/template

The following example is )mostly default) configuration of DECT 1 line. Most of parameters are same as for casual line.

Yes

No

30

No

$NOTIFY

$PROXY

0x68

3

0xb8

6

high

Yes

UDP

5062

No

Yes

No

none

0

No

4

0

No

Yes

No

Yes

3

No

Yes

No

3600

No

3600

Normal

2147483647

No

Yes

No

Yes

G711u

Unspecified

No

Default

No

medium

Yes

Auto

Strict

None

No

(*xx|[3469]11|0|00|[2-9]xxxxxx|1xxx[2-9]xxxxxxS0|xxxxxxxxxxxx.)

(S0<:@gw0>)

No

1,2,3,4,5

20

No

manual

source

media

Yes

...

No

020C009A50

0x70

0x3C

0x13

0x08

0x70

0x00

CATiq

1

No

...

wendellprincipe · ‎04-13-2013

Hi Dan,

i tried this /admin/config.xml howeve it is jumbled/encrypted of some sort.

i just noticed you wrote line_enable 4 as your example, is line 4 equal to DECT 1? i tried configuring, line 1-3, and not 4,.. i will try 4 on monday and will post updates.

thanks

wendellprincipe · ‎04-13-2013

for SPA301 and 302 no issues, i have provisioned it correctly, LINE number is directly equivalent with Extension number.

but since SPA232 has PSTN and Phone with 10 Lines, i have not tried reaching line 4 in xml file. i noticed line 1 is equivalent to Phone LINE. line 2 does not affect anyting and line 3 also not affecting anything.

Dan Lukes · ‎04-13-2013

It seems the 1,2 are FXS lines 1 a 2 (well, SPA232D has no line 2, but it is for compatibility with configuration of SPA112). 3 is FXO line (PSTN), 4-13 are DECT 1 - DECT 10

By the way, the SPA232D is ATA device, not SPA IP phone, so you should move this thread to

Use "move" command on the top right menu.

wendellprincipe · ‎04-13-2013

Hi Dan, sure will move the thread and will try to configure ata tomorrow.. Ty