04-22-2011 07:44 AM - edited 03-21-2019 03:59 AM
A site wants all MWIs turned off. A cisco tech gave me this command to run from CUE CLI:
ccn application ciscomwiapplication aa
no enabled
end
All of the MWIs are turned off on all phones except for one. Even if the user has no voicemails, the phone still lights up the MWI.
I setup a softphone with that extension. The MWI was lit on the softphone as well. I tried removing and readding the ephone dn but that did not make a difference.
I tried multiple MWI refreshes with no change.
I could try to remove and readd the mailbox but I am trying to avoid that.
Does anyone have any ideas?
Solved! Go to Solution.
04-22-2011 12:31 PM
Can you dial the MWI off number? For example, if the MWI off number is 1000 and the DN in question is 2000, try dialing 10002000 from the phone.
Hope this helps.
Brandon
04-22-2011 12:31 PM
Can you dial the MWI off number? For example, if the MWI off number is 1000 and the DN in question is 2000, try dialing 10002000 from the phone.
Hope this helps.
Brandon
04-22-2011 03:57 PM
Hi Jason,
You can use CCA as well in the topology view and right click on the phone itself and refresh MWI status, I have heard this can sometimes resolve that problem, although I am not too certain what it does in the background, probably does what Brandon suggested even
Cheers,
David.
04-25-2011 07:07 AM
When I ran the show ephone registered command, I noticed something interesting. Maybe it is related. Maybe it is not. I bolded the lines in question. On all other phones, button 1 says just 'shared with monitor-ring.' The phone that is having a problem says 'mwi shared with monitor-ring.' I am not sure how to change this. The dn's for these phones are identical in configuration.
ephone-4[3] Mac:001D.E5EA.9C8E TCP socket:[11] activeLine:0 whisperLine:0 REGISTERED in SCCP ver 8/8 max_streams=1 SPCP ver 1/1
mediaActive:0 whisper_mediaActive:0 startMedia:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:12 privacy:1
IP:192.168.10.15 * 27628 CP-524G keepalive 13434 max_line 4 available_line 4 DnD
button 1: cw:1 ccw:(0 0)
dn 84 number 101 CH1 IDLE CH2 IDLE mwi shared with monitor-ring
button 2: cw:1 ccw:(0 0 0 0 0 0 0 0)
dn 82 number 106 CH1 IDLE CH2 IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 IDLE CH7 IDLE CH8 IDLE watch(BLF on phone 6) shared with monitor-ring
button 3: cw:1 ccw:(0 0 0 0 0 0 0 0)
dn 76 number 113 CH1 IDLE CH2 IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 IDLE CH7 IDLE CH8 IDLE watch(BLF on phone 12) shared with monitor-ring
button 4: cw:1 ccw:(0 0 0 0 0 0 0 0)
dn 87 number 102 CH1 IDLE CH2 IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 IDLE CH7 IDLE CH8 IDLE watch(BLF on phone 1) shared with monitor-ring
Preferred Codec: g711ulaw
Lpcor Type: none Username: Office101 Password:
ephone-15[14] Mac:001D.E5EA.9C8B TCP socket:[4] activeLine:0 whisperLine:0 REGISTERED in SCCP ver 8/8 max_streams=1 SPCP ver 1/1
mediaActive:0 whisper_mediaActive:0 startMedia:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:12 privacy:1
IP:192.168.10.14 * 2499 CP-524G keepalive 51352 max_line 4 available_line 4
button 1: cw:1 ccw:(0 0)
dn 73 number 104 CH1 IDLE CH2 IDLE shared with monitor-ring
button 2: cw:1 ccw:(0 0)
dn 84 number 101 CH1 IDLE CH2 IDLE mwi watch(BLF on phone 16) shared with monitor-ring
button 3: cw:1 ccw:(0 0 0 0 0 0 0 0)
dn 75 number 103 CH1 IDLE CH2 IDLE CH3 IDLE CH4 IDLE CH5 IDLE CH6 IDLE CH7 IDLE CH8 IDLE watch(BLF on phone 13) shared with monitor-ring
button 4: cw:1 ccw:(0 0)
dn 77 number 105 CH1 IDLE CH2 IDLE watch(BLF on phone 11) shared with monitor-ring
Preferred Codec: g711ulaw
Lpcor Type: none Username: Office104 Password:
04-26-2011 04:26 PM
Hi Jason,
I have logged into multiple systems and am unable to see the same issue as what your system is representing (Bolded lines).
Is there a way to remove that specific phone configuration and re-instate it?
Also can you show me the config of the ephone itself so I can see how it even shared the lines with the MWI, I was always under the impressing it couldn't do this unless you actually specified it on the ephone itself, which would make no sense to do so
Cheers,
David.
04-27-2011 10:18 AM
ephone 4
device-security-mode none
mac-address 001D.E5EA.9C8E
ephone-template 16
max-calls-per-button 2
username "Office101" password
type 524G
button 1:84 2w82 3w76 4w87
I forgot I setup a softphone with button 1:84 to see if the light lit up on the softphone. It does. I removed the button from the softphone but that did not change the mwi shared monitor config line.
05-02-2011 06:18 AM
I realized mwi shared with monitor-ring just means the MWI is lit up. I think the MWI is in a separate column if there were headings on the columns.
To fix this I changed the following:
ephone-dn 69
number A801... no-reg primary
mwi off
to
ephone-dn 69
number 8001... no-reg primary
mwi off
Then I dialed 8001101 from my phone. That turned the MWI off. I changed it back to A801... just to keep it standard.
Thanks everyone for the help and input.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide