01-12-2004 04:50 PM - edited 02-21-2020 12:59 PM
There are other Cisco VPN Clients Connecting so I;, not sure which errors are for the Netopia and which are for the other clients, but I'll post what I have.
I think the main line that is an Issue is the one that reads:
VPN Peer:ISAKMP: Peer Info for X.Y.Z.A/500 not found - peers:9
I have one Netopia setup and its working just fine. Its connected using pre-shared keys and I have the line:
isakmp key ******* address 0.0.0.0 netmask 0.0.0.0 no-xauth no-config-mode
that allows it to connect without knowing the IP address. This has been working for quite some time.
The new Netopia has a different (newer) firmware and is giving me fits.
Since I've connected the Netopia to the LAN that the outside interface is on I've also tried entering the following with no luck.
isakmp key ******** address X.Y.Z.A netmask 255.255.255.255 no-xauth no-config-mode
No Luck..
Any tips would be appreciated.
Thanks,
Scott<-
ISADB: reaper checking SA 0x15f07e4, conn_id = 0
ISADB: reaper checking SA 0x156ad0c, conn_id = 0
ISADB: reaper checking SA 0x1543d3c, conn_id = 0
ISADB: reaper checking SA 0x15f415c, conn_id = 0
ISADB: reaper checking SA 0x156312c, conn_id = 0
ISADB: reaper checking SA 0x15f78dc, conn_id = 0 DELETE IT!
VPN Peer:ISAKMP: Peer Info for X.Y.Z.A/500 not found - peers:9
ISADB: reaper checking SA 0x15f7154, conn_id = 0
ISADB: reaper checking SA 0x15e5964, conn_id = 0
ISADB: reaper checking SA 0x15ea76c, conn_id = 0
ISADB: reaper checking SA 0x15e779c, conn_id = 0
ISADB: reaper checking SA 0x15ec27c, conn_id = 0
ISADB: reaper checking SA 0x156b494, conn_id = 0
ISADB: reaper checking SA 0x15f07e4, conn_id = 0
ISADB: reaper checking SA 0x156ad0c, conn_id = 0
ISADB: reaper checking SA 0x1543d3c, conn_id = 0
ISADB: reaper checking SA 0x15f415c, conn_id = 0
ISADB: reaper checking SA 0x156312c, conn_id = 0
crypto_isakmp_process_block:src:204.145.245.3, dest:charlie_o spt:500 dpt:500
OAK_AG exchange
ISAKMP (0): processing SA payload. message ID = 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 8 policy
ISAKMP: life type in seconds
ISAKMP: life duration (basic) of 28800
ISAKMP: encryption DES-CBC
ISAKMP: auth pre-share
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 10 policy
ISAKMP: life type in seconds
ISAKMP: life duration (basic) of 28800
ISAKMP: encryption DES-CBC
ISAKMP: auth pre-share
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 11 policy
ISAKMP: life type in seconds
ISAKMP: life duration (basic) of 28800
ISAKMP: encryption DES-CBC
ISAKMP: auth pre-share
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 13 policy
ISAKMP: life type in seconds
ISAKMP: life duration (basic) of 28800
ISAKMP: encryption DES-CBC
ISAKMP: auth pre-share
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 20 policy
ISAKMP: life type in seconds
ISAKMP: life duration (basic) of 28800
ISAKMP: encryption DES-CBC
ISAKMP: auth pre-share
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP (0): atts are not acceptable. Next payload is 0
ISAKMP (0): Checking ISAKMP transform 1 against priority 22 policy
ISAKMP: life type in seconds
ISAKMP: life duration (basic) of 28800
ISAKMP: encryption DES-CBC
ISAKMP: auth pre-share
ISAKMP: hash MD5
ISAKMP: default group 2
ISAKMP (0): atts are acceptable. Next payload is 0
ISAKMP (0): processing KE payload. message ID = 0
ISAKMP (0): processing NONCE payload. message ID = 0
ISAKMP (0): processing ID payload. message ID = 0
ISAKMP (0): ID payload
next-payload : 10
type : 2
protocol : 17
port : 0
length : 27
ISAKMP (0): Total payload length: 31
return status is IKMP_NO_ERROR
ISAKMP (0): retransmitting phase 1...
ISAKMP (0): retransmitting phase 1...
01-19-2004 06:18 AM
Did you try clearing the SA's once you were done with the configurations? It might just work.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide