Re: Linksys BEFSX41 VPN to Pix 515E - Page 4

rod.caglia · ‎12-29-2002

I've been scouring forums and the cisco website to get this vpn going now for

about a week. Total newbie to vpn's :o

I have a 515E at my main site and a couple remotes with linksys befsx41 vpn routers on cable and dsl. The Pix has 3 interfaces, outside, dmz and inside.

I have succesfully setup the Pix for pptp and ipsec using the Cisco Vpn client and was able to access the internal network ok. Now I'm trying to get the linksys connected with no luck. Just to make sure I didn't have any overlapping configurations, I no'd all the vpn client setup to bring the Pix back to a clean config before trying to setup the ipsec site to site.

My main goal is to have the linksys routers initiate the connection and allow 3 or 4 users access over the tunnel to the main site.

Anyone who can guide me in the right direction without having to get my CCIE first I would appreciate it!

TIA

Rod

hwilms5575 · ‎03-22-2006

Rod

Could you please send me a copy of the pix and linksys configs you used to get this working.

Thanks

hwilms@presidio.com

rockhoro · ‎01-10-2003

Rod,

I would appreciate you sending my the document also! Would be a great help as I am working on a total re-design of a system that is not set up correctly. Trying to come in and "clean up" is a hard thing!

Thanks - Ray Rockholt

tpcolson · ‎02-09-2003

yes...how does one gain membership into the secret squirrel society and view these sample configs? ;)

ghartze · ‎02-17-2003

I'm also trying the same thing to a Linksys BEFSX41 to PIX515 or VPN3000 Concentrator. Please forward configs as well...thanks :)

rmalally · ‎02-21-2003

I am also working on this, could someone forward me the configs.

Thanks

jafranklin · ‎03-31-2003

Rod could you send me a copy of your cfg. I just read your posting and that is something I am interested in trying out for some of our remote sites. Typically I have used cisco to cisco solutions, but would like to try a more cost effective route if possible. Thanks

paul · ‎04-06-2003

Hi there,

Count me in too. Please send me a copy of your configs to paul@iqon-asia.com

Best Regards,

Paul

josewilson · ‎04-09-2003

Hey Rod,

Please send me a copy of your configs to josewilson@infomgmt.com

Thanks..

tonyng42 · ‎04-18-2003

Can you send me your config and how you set things up? I am also trying the same thing. Also, what type of user authentication are you using? I need to use local authentication...

My email address is tcconsulting42@yahoo.com. Thanks in advance.

peter.wilson · ‎04-21-2003

Rod,

I'm trying to connect a linksys BEFSX41to a pix 525 and having no luck. Could you send me the linksys/pix config?? It will save me alot of sleep and headache!!!

Thanks in advance!!

Pete wilsonph@shaw.ca

peter.wilson · ‎04-22-2003

Has anyone setup a pix with multiple vpn connections?? My current PIX vpn uses RSA authentication and I need to exclude the linksys ip or figure out how to use both at once. Thanks,

Pete

cvdata · ‎05-05-2003

Please send me the configs also. dpeterson@cv-data.com

lams · ‎07-17-2003

Hi there,

Can you please send me a copy of your config. Thanks!

lams@imsg.com

scharb · ‎08-29-2003

Hi Rod,

I do not have a linksys but I would like to see your config. Email to bobschaber@columbus.rr.com

rayala · ‎09-26-2003

Hey Rod,

Can anybody send me a copy of this configurations. It would really help me a lot. rayala@tel-datacommunications.com