Linksys BEFSX41 VPN to Pix 515E

[rod.caglia]

I've been scouring forums and the cisco website to get this vpn going now for

about a week. Total newbie to vpn's :o

I have a 515E at my main site and a couple remotes with linksys befsx41 vpn routers on cable and dsl. The Pix has 3 interfaces, outside, dmz and inside.

I have succesfully setup the Pix for pptp and ipsec using the Cisco Vpn client and was able to access the internal network ok. Now I'm trying to get the linksys connected with no luck. Just to make sure I didn't have any overlapping configurations, I no'd all the vpn client setup to bring the Pix back to a clean config before trying to setup the ipsec site to site.

My main goal is to have the linksys routers initiate the connection and allow 3 or 4 users access over the tunnel to the main site.

Anyone who can guide me in the right direction without having to get my CCIE first I would appreciate it!

TIA

Rod

[lheredia]

Hi!:

were you able to solve the problem?? I am having the same issue... could you send me your configs if possible?

Thanks a lot!

Luis

[coxendine]

Rod,

Can I get a copy of the configuration for the PIX and the Linksys. Thanks in advance for all your help. coxendine@firsthealth.org

-Cal

[plemieux72]

Me too please... Working on same thing. Thanks! :)

[pupang]

Please add me to the long list of folks who would also like to know how to get this running!

Please e-mail me your configs!

Thanks

Robert Beveridge

beveridr@genco.com

[m.milano]

Rod. My name is Marcelo. If you still have this configuration I will apreciate you send them to me.

My email is m.milano@grader.com.ar

Thak you very much!

[email]

I if you would be kind enough to email me the configuration for both the linksys and the pix.

thankyou in advanced.

email@webersupply.com

[dustinbeaudry]

Could you possibly send your config to me as i have not been able to get the linksys to connect to our Pix 515. Frustrating to say the least! Thanks so much in advance.

db@pegasusinvestors.com

[m.milano]

Dustin. I was not able to get the linksys BEFSX41 to connect ti Pix 515. The problem is that when I tried to make the tunnel, the Linksys went down. I was talking with Cisco TAC and Linksys TAC. The final answer from Linksys was that the Linksys BEFSX41 doesn´t work and I have to use BEFVP41. I made a test with this model and I have no problems.

Regards.

[dustinbeaudry]

thats too bad - thanks though. I was hoping to add wireless to the mix. One question though - if i get the BEFVP41 will that work from a cable modem that doesnt have a static ip? Thanks again for you help. Much appreciated.

[m.milano]

Dustin.

The BEFVP41 support static ip, pppoe or DHCP (to work from a cable modem).

Regards.

[aleuluai]

Please send me the link.

aleuluai@kbhome.com

[sakdavin]

Dear Rod,

I am going to implement pix firwall 515e and Linksys router with three branches as your case. could you email me the linksys and pix firewall 515e configuration. I think your solution would be every useful for me.My email address is vin@firstcambodia.com

Thanks in advances.

Sakdavin

[sakdavin]

Hello Rod,

I am very interested in your information.And I do need your help, coz i am going to implement Pix firewall 515e and linksys as your above case.

So please kindly send me the configuration via my email address is vin@firstcambodia.com

You help is much appreciated.

Thanks in advances.

Sakdavin

[sakdavin]

Hello Rod,

I am very interested in your information.And I do need your help, coz i am going to implement Pix firewall 515e and linksys as your above case.

So please kindly send me the configuration via my email address is vin@firstcambodia.com

You help is much appreciated.

Thanks in advances.

Sakdavin

[p.parra]

Hi Rod,

Could you send me the configuration for the Pix and Linksys, please?

Thanks in advanced.