04-18-2011 12:20 PM
Upgrading ACS 5.1.0.44.6 appliance
to 5.2.0.26. I submited command
"application upgrade ACS_5.2.0.26.tar.gz upgrade-repository" and got this error after replying yes to save the configuration and then got this error.
Do you want to save the current configuration ? (yes/no) [yes] ? yes
Generating configuration...
Saved the running configuration to startup successfully
% Manifest file not found in the bundle
Any ideas?
05-13-2011 08:52 AM
Hi Ernie,
Double check the command used, is totally different the "patch" command and the "acs patch". The former patches the system, the later patches the acs application.
The correct command syntax is acs patch install -----.gpg repository ------
Hope it helps:)
Jaime
05-19-2011 11:04 AM
Hello Jaime. This is not a patch, this an upgrade from 5.1.0.44.6 to 5.2.0.26 and Cisco says to do the following:
Instructions on how to install the application bundle
=====================================================
1. open CLI console.
2. define new repository in which the ACS_5.2.0.26.tar.gz resides.
3. issue: 'application upgrade ACS_5.2.0.26.tar.gz YOUR_REPOSITORY'
4. The system will reboot in few minutes.
5. After reboot login to the CLI and verify the acs & adeos version by issuing "show version" command.
ADE-OS Build Version: 1.2.0.182
Cisco ACS VERSION INFORMATION
-----------------------------
Version : 5.2.0.26
Thanks, Ernie
09-12-2011 03:29 PM
Does anybody find the solution for this message?
09-30-2011 08:31 AM
Hi all,
the problem is you are probably trying to perform the upgrade via TFTP. The file will be transferred between your Repository and the ACS, however the upgrade will not work and you will receive the latter error message.
As stated in the upgrade manual (although written in very small letters) :
"You must have a repository configured with an FTP, NFS, or SFTP network server (but not a TFTP repository) to perform the ACS upgrade."
Good luck with it!
Cheers,
Wouter
09-30-2011 09:27 AM
HI Wouter, I used FTP and works perfect. Thanks.
04-19-2014 06:17 AM
Check /storedata:
4.9G 3.0G 1.7G 65% /storeddata
After reloading the ACS:
4.9G 683M 4.0G 15% /storeddata
04-21-2014 11:59 PM
Hi,
I used the TFTP method, it worked perfectly.
In addition to that, you have to use the ACS patch command option ONLY works..
Example: acs patch install 5-5-0-46-2.tar.gpg repository test
Note: You have to create a repository before applying the above mentioned command.
Config Example:
config t
repository test
url tftp://10.1.1.1
exit
IP address: 10.1.1.1, where you mapped the TFTP server is running..
Good luck, it will work perfectly, if not let me know steps you tried.
08-26-2014 01:38 AM
Hello,
I try to upgrade an ACS/VM from ACS 5.3 (Acs-5-3-0-40-9 with the preupgrade fix Pointed-PreUpgrade-CSCum04132-5-3-0-40.tar.gpg) to ACS 5.5.
radius/didata# show application version acs
Cisco ACS VERSION INFORMATION
-----------------------------
Version : 5.3.0.40.40
Internal Build ID : B.839.EVAL
Patches :
5-3-0-40-2
5-3-0-40-9
Pointed-PreUpgrade-CSCum04132-5-3-0-40
I got the same error message:
Do you want to save the current configuration ? (yes/no) [yes] ?
Generating configuration...
Saved the running configuration to startup successfully
% Manifest file not found in the bundle
I have enough space on the VM partition.
Thank you for your idea/solution.
Best regards
Bernard
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide