Small Business Support Community

cisco sg350-10 halp_config_poe_number_of_poe_devices is zero. failed o

Hello everyone,My Cisco SG350-10 switch is unable to complete its boot sequence. Unfortunately, it always stops with the following error:HALP_config_poe_number_of_poe_devices is Zero: Failed on init (This message was captured through the rear se...

Cannot login to 192.168.1.1

I want to configure my RVS4000 router but find that I am unable to login to the 192.168.1.1 site to do so. The "admin" username and password is not working. Maybe I do not have to as my internet connection seems to be working fine. ...

C1300 - Tagged VLAN traffic not forwarding on trunk to/from Firewall

Setup: Cisco C1300-12XT-2X, firmware 4.1.9.85 (latest). Interface te1/0/13 is an 802.1Q trunk to a WatchGuard Firebox M690 (WG physical interface 10, also configured as a tagged trunk).Trunk config on te1/0/13:interface TenGigabitEthernet1/0/13switch...

C1300 switchs

1- C1300-48FP-4X Catalyst 1300 - 38876627+48-Port GE, Full POE, 4X10G SFP2- C1300-24FP-4X Cisco C1300 - 30798414Switch, 24x PoE+ 370W/4x 10G SFP+/Rackmountable May i know if this switches are out of support ?

Resolved! Cisco C1300-24T hardware revision update

Hi,we are using the Cisco C1300-24T-4G for some time and recently we found out that a new hardware revision has been released. The PCN Cisco provided states that only the label "country of origin" changed but we run into problems when we install firm...

RV345 no access after firmware update to RV34X-v1.0.03.26

I did a config backup.I downloaded 1.0.0.3.26 and did the update (without reset to factory checked).When completed, the webgui login page was corrupt. It had spinning icon beside what should be the login button. see pic.I tried old logins, but i dont...

check serial FJC272611BF

Cisco Smartnet Renewal Subscription

dear sir/madam,Kindly provide the solution for the cisco Renewal Smartnet. please multiple options for Cisco SmartNet renewal.

Resolved! Cisco Smartnet Renewal concerns

dear Sir/madam,I am requesting the cisco SmartNet renewal is mandatory for all access switches and core switches. is there any options minimize the cost. please provide the multiple options for SmartNet renewal. RegardsSyed MustafaIT Network Eng.,053...

Resolved! Cisco warranty check

Good day, can you help me to check the warranty of my Cisco conferencing kitCS-KIT-K9-ModelSFOC2334N3AZ -Serial numberThanks and Best Regards

150AX on different subnets ?!

While migrating away from a legacy setup, we're adding a bunch of 150AX into our production network which will live on different VLANs. These VLANs are routed transparently, meaning traffic can flow freely between them. After adding two 150AX on VLA...

Resolved! Access Control Lists - Clarification: The Inside Global address

I mostly think I understand the format of the ACL statements, but I need some clarification the "Inside Global Address".The web examples I have found seem to usually use the FastEthernet4 IP address which is the feed IP from the ISP. However, I'm wo...

Resolved! How to find manuals for switch series CBS220 and AP CBW150AX?

I ordered a switch and an AP to recreate our small bussiness network. Before starting to recreate the network, I would like to download the documentation and manuals for the devices. As for now I only found descriptions of partial configurations. How...

CWB 240 low transmit power

Hello there, have tree CBW 240ac accespoints at home. Problem is that I am not able to determine how to change signal transmit power for both 2.4 and 5ghz.I have 20MHz an all of them for 2,4GHz, non overlaping channels (so 1,6,11) set manually. Power...

Resolved! UC320W Firmware

Does anyone where to download the firmware files for the UC320W? I have never seen a company (especially Cisco) just remove a device and downloads from their site before. I can still download ancient ASA code.Need this because one of 320's died fro...