- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-27-2021 04:01 PM
Hi Folks, I am trying to configure an AIR-LAP1142N-S-K9. From what I can see it has a Autonomous boot image.
Secondary bootloader Ethernet not enabled, skip ether_init
Unable to locate IOS image with name **xx**.
Boot CMD: 'boot flash:/c1140-k9w7-mx.153-3.JD16/c1140-k9w7-xx.153-3.JD16'
Loading "flash:/c1140-k9w7-mx.153-3.JD16/c1140-k9w7-xx.153-3.JD16"...####################################
File "flash:/c1140-k9w7-mx.153-3.JD16/c1140-k9w7-xx.153-3.JD16" uncompressed and installed, entry point: 0x4000
executing...
I have set an IP address on the local gigabit interface (through the CLI):
Interface IP-Address OK? Method Status Protocol BVI1 unassigned YES DHCP up up Dot11Radio0 unassigned YES unset administratively down down Dot11Radio1 unassigned YES unset administratively down down GigabitEthernet0 192.168.110.2 YES manual up up
The device is powered using an external power adapter and (currently) all I am using is the console cable into the device.
From the CLI I can ping 192.168.110.2.
If I plug a computer into the 1142's Ethernet port and that computer is on the same subnet (/24) I am unable to ping the 1142 from the computer.
Do I need to have a switch to perform any initial configuration (for example the 1142 relies on the BVI or VLAN information)? I assumed that I could "just" plug a computer in and at the very least "see" the 1142.
Any guidance is appreciated.
Solved! Go to Solution.
- Labels:
-
Other Switching
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-27-2021 11:56 PM
- I think you may need to configure BVI1 instead and or check this thread for hints :
https://community.cisco.com/t5/wireless/setting-up-air-ap1141n-a-k9/td-p/1619818
M.
-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-27-2021 11:56 PM
- I think you may need to configure BVI1 instead and or check this thread for hints :
https://community.cisco.com/t5/wireless/setting-up-air-ap1141n-a-k9/td-p/1619818
M.
-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-28-2021 03:20 PM
Thank you, Marce.
With BV1 configured I was able to access the access point through a computer Ethernet interface.
Interface IP-Address OK? Method Status Protocol BVI1 192.168.110.2 YES manual up up Dot11Radio0 unassigned YES unset administratively down down Dot11Radio0.10 unassigned YES unset administratively down down Dot11Radio0.101 unassigned YES unset administratively down down Dot11Radio1 unassigned YES unset administratively down down Dot11Radio1.10 unassigned YES unset administratively down down GigabitEthernet0 192.168.110.2 YES manual up up GigabitEthernet0.10 unassigned YES unset up up GigabitEthernet0.101 unassigned YES unset up up
