Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Can someone please help with documentation about the new ap 2802 or tell me what can i do to get out of this prompt and join to a WLC.
Resolved! WLC HA redundancy statistics ！
Hi， I dont have wlc for testing.I want to know what is meaning of “ping request and response” in wlc GUI “monitor > redundancy > statistics”.Is it represents do a auto ping or manual ping on active wlc and standby wlc? And whether the “sent to peer” ...
HI Everyone, I looked at the interface details and noticed that all dynamic-interfaces have the same MAC address. And it is basically the same as the MAC address of the management interface. My WLC is 5508, and I want to know how the Cisco WLC assign...
Anybody know what is the correct path for upgrading appliance MSE 7.6.100.0 to MSE 8.0.150.0? The 8.0.150.0 release notes is confusing at least. https://www.cisco.com/c/en/us/td/docs/wireless/mse/release/notes/mse8_0_150.html It has a section with a ...
Hi, For security reasons I need to regenerate the certificate for the https management GUI of a WLC 5508 SSO, since the hash algorithm that has the self-signed certificate of when it is installed is SHA1 and I need it to be SHA256. I have been able t...
Is there a way to limit the number of logins from a particular set of credentials in Cisco Prime 2.1? I want to set a maximum of 2 logins from a particular user on the wlan. I have a guest wlan using layer 3 security and an internal wlan using RADIUS...
Hi all I have a question about the WLC N+1 redundancy. I have 3 Cisco WLC 5520. Can i configure one as Active, one as Standby and the last one will take over when the active and the passiv are down. The failover should be like this.1. Active fails2....
HelloI have a cisco controller 5520 with more than 300 access points joining it, I found that most of the access points like 250 out of 300 are working on the maximum power level 1 on 5g band only, while on 2.4 bands the power level is within normal ...
We are implementing a VLAN in a confined environment which combines both wired and wireless connections. We currently have multiple Full HD (1920x1200) video cameras, each streaming >3.3Gbps, so we are using 10Gig switch over RJ45. The video is multi...
please is there any one help me in this issue *spamApTask1: Nov 20 13:01:57.053: #LWAPP-3-REPLAY_ERR: spam_lrad.c:37692 The system has received replay error on slot 0, WLAN ID 2, count 3 from AP 28:6f:7f:0c:62:30*spamApTask5: Nov 20 13:01:15.593: #L...
Hello Experts, I have one SSID which having RADUIS authentication but when client try's to connect it ..it fails ... here are the logs from thecontroller. Dot1x_NW_MsgTask_0: Nov 07 13:05:08.371: %DOT1X-3-INVALID_WPA_KEY_MSG_STATE: [PA]1x_eapkey.c...
Resolved! Setting a Port Number for WLC Syslog
Hi Guys,Is it possible to set up a port number for syslog on WLC 5520? On the switch we can set it up by issuing the command logging "host 192.168.100.100 transport udp port 5678", but so far I did not find it for WLC.
My Cisco AP 2802i Not Joining with WLC-2500. it is the only ap i want to connect to WLC.[*12/05/2019 17:30:38.3775] SYS-COND: AP is in fair condition[*12/05/2019 17:30:38.8789] DOT11_CFG[0] Radio Mode is changed from Local to Local[*12/05/2019 17:30:...
I am wanting to enable rogue detection on my 5520 WLC's for the purposes of detecting rogue AP's connected to the wired network. Is RLDP required to get an alert from the WLC/Cisco Prime? Has anyone had any experience with enabling RLDP, and are th...
We have an existing concert hall that was never planned for WiFi coverage. We will have to do runs for the lower level. A picture is below. The upper level can hold 570 people. The facility is about 100x100 feet with the inner portion of 68x75' be...
