ā02-21-2012 10:33 AM - edited ā07-03-2021 09:37 PM
I am having trouble getting a 1200 series AP to join our controller. We have 1252's and 1242's sucessfully connected. We are running the latest code on the controller. The LWAP image on the AP is c1200-rcvk9w8-tar.124-21a.JA2. This is what the AP says over the console connection:
*Mar 1 00:00:06.642: %LWAPP-3-CLIENTEVENTLOG: Unable to open event log file flash:/event.log
*Mar 1 00:00:06.644: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 0 messages)
*Mar 1 00:00:07.660: STUB Called : crypto_ssl_init
*Mar 1 00:00:08.761: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:08.798: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1200 Software (C1200-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:06 by prod_rel_team
*Mar 1 00:00:08.835: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:09.761: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:18.133: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.92.26, mask 255.255.255.0, hostname AP0015.6366.e33f
Translating "CISCO-CAPWAP-CONTROLLER.2000domain.hscast.com"...domain server (192.168.128.1)
Translating "CISCO-LWAPP-CONTROLLER.2000domain.hscast.com"...domain server (192.168.128.1)
*Mar 1 00:00:38.677: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:00:38.679: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.2000domain.hscast.com
*Mar 1 00:00:38.683: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.2000domain.hscast.com
*Mar 1 00:00:48.685: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Feb 21 16:38:42.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.128.8 peer_port: 5246
*Feb 21 16:38:42.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Feb 21 16:38:43.893: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.128.8 peer_port: 5246
*Feb 21 16:38:43.895: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.128.8
*Feb 21 16:38:43.896: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Feb 21 16:38:43.905: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.128.8
*Feb 21 16:38:43.905: %DTLS-5-PEER_DISCONNECT: Peer 192.168.128.8 has closed connection.
*Feb 21 16:38:43.906: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 192.168.128.8:5246
examining image...
*Feb 21 16:38:43.907: %CAPWAP-3-ERRORLOG: Go join a lwapp controller
*Feb 21 16:38:43.907: %LWAPP-3-CLIENTERRORLOG: Set Transport AddressCalled
*Feb 21 16:36:17.690: %LWAPP-5-CHANGED: CAPWAP changed state to IMAGE
*Feb 21 16:36:20.715: %CAPWAP-3-ERRORLOG: DTLS connection not found Failed to encrypt and send packet.
*Feb 21 16:36:20.716: %CAPWAP-3-ERRORLOG: Failed to send Join request to 192.168.128.8
%Error opening lwapp:/c1200 (Incorrect Login/Password)
archive download: takes 6 seconds
*Feb 21 16:36:23.691: %LWAPP-3-CLIENTERRORLOG: Retransmission count for type (IMAGE_DATA) exceeded more than max(1)
It repeats this over and over. I can get the controller log as well, if need be. Please help!
Solved! Go to Solution.
ā02-21-2012 12:05 PM
yeah you would have to go back to a 7.0. I'd go with the latest 7.0 code
Steve
ā02-21-2012 10:45 AM
What version of code are you running on the WLC? Can you capture the following debugs concurrently?
debug mac address < ap mac>
debug capwap events
debug capwap erros
Steve
ā02-21-2012 10:45 AM
Did you add the ap 1200 mic/ssc to the 5508?
Thanks,
Scott Fella
Sent from my iPhone
ā02-21-2012 11:59 AM
ā02-21-2012 12:00 PM
ok. 7.2 does not support the 1200 AP. 1130, 1240 and anything newer.
Steve
ā02-21-2012 12:04 PM
Ah. Ok. Thank you. Would we have to go back to an older code to support them? And if so, which version?
ā02-21-2012 12:05 PM
yeah you would have to go back to a 7.0. I'd go with the latest 7.0 code
Steve
ā02-21-2012 12:07 PM
Thank you very much Stephen. We will do that.
ā02-13-2014 11:23 PM
ā02-14-2014 09:00 AM
Hi Karen,
Can you please create a new thread and post these details.
From WLC: sh sysinfo
From AP: sh version
Regards
ā02-17-2014 01:46 AM
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... rt-wlc001
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.0.1.105
Last Reset....................................... Software reset
System Up Time................................... 5 days 20 hrs 58 mins 30 secs
System Timezone Location......................... (GMT +4:00) Muscat, Abu Dhabi
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... RU - Russian Federation
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +44 C
External Temperature............................. +26 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 4
Number of Active Clients......................... 4
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ E4:C7:22:AB:12:60
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 500
AP0018.1823.cd29#sh version
Cisco IOS Software, C1200 Software (C1200-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:06 by prod_rel_team
ROM: Bootstrap program is C1200 boot loader
BOOTLDR: C1200 Boot Loader (C1200-BOOT-M) Version 12.3(2)JA4, RELEASE SOFTWARE (fc1)
AP0018.1823.cd29 uptime is 0 minutes
System returned to ROM by power-on
System image file is "flash:/c1200-rcvk9w8-mx.124-21a.JA2/c1200-rcvk9w8-mx.124-21a.JA"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
cisco AIR-AP1231G-E-K9 (PowerPC405GP) processor (revision A0) with 15038K/1336K bytes of memory.
Processor board ID FCZ1027Z2PK
PowerPC405GP CPU at 196Mhz, revision number 0x0145
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:18:18:23:CD:29
Part Number : 73-8704-11
PCA Assembly Number : 800-23211-12
PCA Revision Number : A0
PCB Serial Number : FOC102326L5
Top Assembly Part Number : 800-23304-13
Top Assembly Serial Number : FCZ1027Z2PK
Top Revision Number : A0
Product/Model Number : AIR-AP1231G-E-K9
Configuration register is 0xF
AP0018.1823.cd29#
ā02-17-2014 02:00 AM
HI Karen,
As per your information:
Product Name..................................... Cisco ControllerProduct Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... rt-wlc001
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.0.1.105
Last Reset....................................... Software reset
System Up Time................................... 5 days 20 hrs 58 mins 30 secs
System Timezone Location......................... (GMT +4:00) Muscat, Abu Dhabi
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... RU - Russian Federation
AP0018.1823.cd29#sh version
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:18:18:23:CD:29
Part Number : 73-8704-11
PCA Assembly Number : 800-23211-12
PCA Revision Number : A0
PCB Serial Number : FOC102326L5
Top Assembly Part Number : 800-23304-13
Top Assembly Serial Number : FCZ1027Z2PK
Top Revision Number : A0
Product/Model Number : AIR-AP1231G-E-K9
Configuration register is 0xF
AP0018.1823.cd29#
1. 1231G AP can only support 7.0.x series and you have the higher version(7.4.100.0).
2. You have regulatery domain -E- on AP and you must use -R- Domin on AP
If you want to connect this AP to WLC then you must downgrade it.
Here is the compatibilty matrix:
Regards
Dont forget to rate helpful posts
ā02-17-2014 04:12 AM
Ok!!!
Thank you it's solve my problem
ā02-17-2014 04:22 AM
Dont forget to rate helpful posts, its encorages us.
Regards
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide