cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
422
Views
0
Helpful
1
Replies
Chris Callison
Beginner

9130axi cannot add a new AP

I have a C9130axi running 17.3.3 in EWC mode.

I would like to add an additional AP (3802i).

 

I have added the new AP to a Cisco Catalyst 3850:

 

interface GigabitEthernet1/0/25
description "Cisco 9130axi EWC AP"
switchport trunk native vlan 424
switchport trunk allowed vlan 423-426,997,998
switchport mode trunk
spanning-tree portfast
!
interface GigabitEthernet1/0/26
description "Cisco 3802i AP"
switchport trunk native vlan 424
switchport trunk allowed vlan 423-426,997,998
switchport mode trunk
spanning-tree portfast

 

POE is working

 

stand#sho power inline | include on
Gi1/0/25 auto on 30.0 C9130AXI-B 4 30.0
Gi1/0/26 auto on 30.0 AIR-AP3802I-B-K9 4 30.0

 

CDP & LLDP are both seeing the devices

 

I added the new AP through the webgui "Configuration | Wireless | Access Points" using the base mac address, but that didn't help.

 

I have also tried changing the settings "Authorize APs against MAC" and "Authorize APs against Serial Number" from disabled to enabled, but that didn't help, either.

 

The AP is going through sequence this over and over.

 

[*08/10/2021 18:18:00.5056] CAPWAP State: Discovery
[*08/10/2021 18:18:00.5106] Discovery Request sent to 192.168.42.130, discovery type STATIC_CONFIG(1)
[*08/10/2021 18:18:00.5115] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*08/10/2021 18:18:00.5132] Discovery Response from 192.168.42.130
[*08/10/2021 18:18:10.0002] Discovery Response from 192.168.42.130
[*08/10/2021 18:18:10.0000]
[*08/10/2021 18:18:10.0000] CAPWAP State: DTLS Setup
[*08/10/2021 18:18:10.0474] dtls_load_ca_certs: LSC Root Certificate not present
[*08/10/2021 18:18:10.0474]
[*08/10/2021 18:18:10.0500]
[*08/10/2021 18:18:10.0500] CAPWAP State: Join
[*08/10/2021 18:18:10.0536] Sending Join request to 192.168.42.130 through port 5272
[*08/10/2021 18:18:10.0572] Invalid event 10 & state 5 combination.
[*08/10/2021 18:18:10.0572] CAPWAP SM handler: Failed to process message type 10 state 5.
[*08/10/2021 18:18:10.0572] Failed to handle capwap control message from controller - status 1
[*08/10/2021 18:18:10.0573] Failed to process encrypted capwap packet 0x26b3000 from 192.168.42.130
[*08/10/2021 18:18:10.0573] Failed to send capwap message 0 to the state machine. Packet already freed.
[*08/10/2021 18:18:10.0573] IPv4 wtpProcessPacketFromSocket returned 1
[*08/10/2021 18:18:10.0574] Join Response from 192.168.42.130
[*08/10/2021 18:18:10.1342] HW CAPWAP tunnel is ADDED
[*08/10/2021 18:18:10.1490]
[*08/10/2021 18:18:10.1490] CAPWAP State: Image Data
[*08/10/2021 18:18:10.1798] do NO_UPGRADE, part1 is active part
[*08/10/2021 18:18:10.1830]
[*08/10/2021 18:18:10.1830] CAPWAP State: Configure
[*08/10/2021 18:18:10.1857] NO-ENC-PROVIDER for DOT11R_WLC_MAC_IP_PAYLOAD
[*08/10/2021 18:18:41.5488] Re-Tx Count=11, Max Re-Tx Value=5, NumofPendingMsgs=1
[*08/10/2021 18:18:41.5488]
[*08/10/2021 18:18:44.3996] Re-Tx Count=12, Max Re-Tx Value=5, NumofPendingMsgs=1
[*08/10/2021 18:18:44.3996]
[*08/10/2021 18:18:47.2504] Re-Tx Count=13, Max Re-Tx Value=5, NumofPendingMsgs=1
[*08/10/2021 18:18:47.2504]
[*08/10/2021 18:18:50.1013] Re-Tx Count=14, Max Re-Tx Value=5, NumofPendingMsgs=1
[*08/10/2021 18:18:50.1013]
[*08/10/2021 18:18:52.9521] Re-Tx Count=15, Max Re-Tx Value=5, NumofPendingMsgs=1
[*08/10/2021 18:18:52.9521]
[*08/10/2021 18:18:53.6370] Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Configure(8).
[*08/10/2021 18:18:55.8029] Re-Tx Count=16, Max Re-Tx Value=5, NumofPendingMsgs=1
[*08/10/2021 18:18:55.8029]
[*08/10/2021 18:18:55.8030] Max retransmission count exceeded, going back to DISCOVER mode.
[*08/10/2021 18:18:55.8030] GOING BACK TO DISCOVER MODE
[*08/10/2021 18:18:55.8035]
[*08/10/2021 18:18:55.8035] CAPWAP State: DTLS Teardown

1 REPLY 1

Try use the archive command on the 38 with the downloaded tar file thru tftp.

 

Create
Recognize Your Peers
Content for Community-Ad