Hey, I'm trying to add a new AP to the controller. Cisco Aironet Series Mobiliy Expres version 8.10.190.0. AP visible, I run the tftp server with the software. Unfortunately, the AP does not update and downloads the software again.
AP is AIR-AP2802E-E-K9
[*11/03/2023 09:02:55.2869] Successfully downloaded image.
[*11/03/2023 09:02:55.3176] do PREDOWNLOAD, part1 is active part
[*11/03/2023 09:02:56.0778] Image signing verify success.
[*11/03/2023 09:02:56.0885] upgrade.sh: part to upgrade is part2
[*11/03/2023 09:03:09.2321] tar: write error: No space left on device
[*11/03/2023 09:03:09.2339] upgrade.sh: Command "tar -xf /tmp/part.tar -C /bootpart/part2" failed.
[*11/03/2023 09:03:09.2353] upgrade.sh: df /bootpart/part2
[*11/03/2023 09:03:09.2382] upgrade.sh: du -h /bootpart/part2
[*11/03/2023 09:03:09.2407] upgrade.sh: Writing image to disk...
[*11/03/2023 09:03:09.2876] sh: 1K-blocks: unknown operand
[*11/03/2023 09:03:09.3856] upgrade.sh: AP backup version: 8.10.190.0
[*11/03/2023 09:03:09.5669] do ACTIVATE, part1 is active part
[*11/03/2023 09:03:09.6677] upgrade.sh: activate part2, set BOOT to part2
[*11/03/2023 09:03:10.3143] upgrade.sh: AP primary version: 8.10.190.0
[*11/03/2023 09:03:10.3158] upgrade.sh: AP backup version: 8.3.143.0
[*11/03/2023 09:03:13.3210] AP Rebooting: Reset Request from Controller(Image Upgrade)
Writing reload timestamp (Fri Nov 3 09:03:13 UTC 2023) to disk
[*11/03/2023 09:03:14.3664] umount: can't umount /storage: Device or resource busy
failed to unmount /storage; waiting 1s and trying again.
The system is going down NOW!09:03:15.3696]
[*11/03/2023 09:03:15.3744] 2023-11-03 09:03:15 TAMS terminating due to signal 15 (Terminated)
[*11/03/2023 09:03:15.3745] 2023-11-03 09:03:15 select errno=4 - Interrupted system call
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system reboot77]
[11/03/2023 09:03:17.3700] reboot: Restarting system
BootROM - 1.78
Booting from SPI flash, Secure mode
BootROM: RSA Public key verification PASSED
BootROM: CSK block signature verification PASSED
BootROM: Boot header signature verification PASSED
BootROM: Box ID verification PASSED
BootROM: JTAG is disabled
General initialization - Version: 1.0.0
Detected Device ID 6920
Master bootloder version 1.4a
High speed PHY - Version: 2.0
BoardId = 0x21board SerDes lanes topology details:
| Lane # | Speed| Type |
------------------------------|
| 1 | 0 | SGMII1 |
| 2 | 5 | PCIe1 |
| 4 | 5 | PCIe2 |
| 5 | 0 | SGMII2 |
-------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 1: Link upgraded to Gen2 based on client cpabilities
:** Link is Gen1, check the EP capability
PCIe, Idx 2: Link upgraded to Gen2 based on client cpabilities
High speed PHY - Ended Successfully
DDR4 Training Sequence - Ver TIP-0.23.(Sublib 0.8)0
DDR4 Training Sequence - Switching XBAR Window to FastPath Window
DDR4 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
BootROM: Boot image signature verification PASSED
____ _
/ ___|(_) ___ ___ ___
| | | |/ __| / __|/ _ \
| |___ | |\__ \| (__| (_) |
\____||_||___/ \___|\___/
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01-ge1c49d93a (Jul 28 2023 - 09:08:14) SDK version: 2015_T2.0p10
Board: Barbados-2K
SoC: MV88F6920 Rev A1
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1800 [MHz]
L2 @ 900 [MHz]
TClock @ 250 [MHz]
DDR4 @ 900 [MHz]
DDR4 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 1 GiB
RST I2C0
NAND: ECC 4bits, 256 MiB
SF: Detected MX25L3205D with page size 64 KiB, total 4 MiB
PCI-e 1 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
PCI-e 2 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 2.0
Map: Code: 0x3fed7000:0x3ffad848
BSS: 0x3ffef314
Stack: 0x3f9c6f20
Heap: 0x3f9c7000:0x3fed7000
U-Boot Environment: 0x00100000:0x00110000 (SPI)
Board configuration:
| port | Interface | PHY address |
|--------|------------|--------------|
| egiga1 | SGMII | 0x01 |
| egiga2 | SGMII | 0x00 |
Net: , egiga1, egiga2 [PRIME]
Hit ESC key to stop autoboot: 0
Creating 1 MTD partitions on "nand0":
0x000000200000-0x000010000000 : "mtd=2"
UBI: attaching mtd1 to ubi0
UBIFS: mounted UBI device 0, volume 1, name "part2"
part2/info.ver not found!
ubifsload - load file from an UBIFS filesystem
Usage:
ubifsload <addr> <filename> [bytes]
- load file 'filename' to address 'addr'
Unable to load altboot info file part2/info.ver
part2/part.bin not found!
ubifsload - load file from an UBIFS filesystem
Usage:
ubifsload <addr> <filename> [bytes]
- load file 'filename' to address 'addr'
Unable to load image part2/part.bin
Trying alternate partition part1
UBIFS: mounted UBI device 0, volume 0, name "part1"
Loading file 'part1/info.ver' to addr 0x02000000 with size 63 (0x0000003f)...
Done
Loading file 'part1/part.bin' to addr 0x02000000 with size 28402073 (0x01b16199)...
Done
SF: Detected MX25L3205D with page size 64 KiB, total 4 MiB
Checking image signing.
Image signing verification success, continue to run...
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Barbados Firmware Image
Created: 2018-06-05 6:31:58 UTC
Image Type: ARM Linux Multi-File Image (uncompressed)
Data Size: 28401065 Bytes = 27.1 MiB
Load Address: 00008000
Entry Point: 00008000
Contents:
Image 0: 4027512 Bytes = 3.8 MiB
Image 1: 24357788 Bytes = 23.2 MiB
Image 2: 15749 Bytes = 15.4 KiB
Verifying Checksum ... OK
## Loading init Ramdisk from multi component Legacy Image at 02000000 ...
## Flattened Device Tree from multi component Image at 02000000
Booting using the fdt at 0x03b12064
Loading Multi-File Image ... OK
OK
Loading Device Tree to 01ff9000, end 01fffd84 ... OK
Starting Device Tree update ('fdt_skip_update' = no)
Limit DDR size at 3GB due to power of 2 requirement of Address decoding
Updating device tree successful
------------------------------------------------------------------------------------------
Processor board ID FGL2227ABJK
AP Running Image : 8.3.143.0
Primary Boot Image : 8.3.143.0
Backup Boot Image : 0.0.0.0
2 Gigabit Ethernet interfaces
2 802.11 Radios
Radio Driver version : 9.0.5.5-W8964
Radio FW version : 9.1.8.1
