AIR-CAP2702I-E-K9 autonomus

[Dirk Meyer]

Good day, I converted an AIR-CAP2702I-E-K9 to an autonomous AP. Unfortunately I can't get the GUI in my browser. Here is the boot log:

IOS Bootloader - Starting system.
flash is writable
Antigua Board
40MB format
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 311 files, 14 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 29484032
flashfs[0]: Bytes available: 11674624
flashfs[0]: flashfs fsck took 11 seconds.
Base Ethernet MAC address: XXXXXX8
Ethernet speed is 1000 Mb - FULL Duplex
Loading "flash:/ap3g2-k9w7-mx.153-3.JPK/ap3g2-k9w7-mx.153-3.JPK"...#########################

File "flash:/ap3g2-k9w7-mx.153-3.JPK/ap3g2-k9w7-mx.153-3.JPK" uncompressed and installed, entry point: 0x2003000
executing...

Secondary Bootloader - Starting system.
Antigua Board Pre-Pilot
40MB format
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 311 files, 14 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 29484032
flashfs[0]: Bytes available: 11674624
flashfs[0]: flashfs fsck took 11 seconds.
flashfs[1]: 0 files, 1 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 12257280
flashfs[1]: Bytes used: 1024
flashfs[1]: Bytes available: 12256256
flashfs[1]: flashfs fsck took 1 seconds.
Base Ethernet MAC address:XXXXXX
Boot CMD: 'boot  flash:/ap3g2-k9w7-mx.153-3.JPK/ap3g2-k9w7-xx.153-3.JPK;flash:/ap3g2-k9w7-mx.153-3.JPK/ap3g2-k9w7-xx.153-3.JPK'
Loading "flash:/ap3g2-k9w7-mx.153-3.JPK/ap3g2-k9w7-xx.153-3.JPK"...###########################################
File "flash:/ap3g2-k9w7-mx.153-3.JPK/ap3g2-k9w7-xx.153-3.JPK" uncompressed and installed, entry point: 0x1003000
executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco IOS Software, C2700 Software (AP3G2-K9W7-M), Version 15.3(3)JPK, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2020 by Cisco Systems, Inc.
Compiled Tue 24-Nov-20 03:58 by prod_rel_team

Antigua Board Pre-Pilot
40MB format
Tide XL MB - 40MB of flash
Initializing flashfs...

flashfs[2]: 311 files, 14 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 40900608
flashfs[2]: Bytes used: 29484032
flashfs[2]: Bytes available: 11416576
flashfs[2]: flashfs fsck took 12 seconds.
flashfs[2]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 1 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCCCC
Copy in progress...CCC
Copy in progress...CCCC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CCCCCCCC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...C
Uncompressing radio files...
...done Initializing flashfs.

Radio0  present 8764 8000 0 A8000000 A8010000 0
Rate table has 650 entries (20 legacy/224 11n/406 11ac)

POWER TABLE FILENAME = ram:/U2.bin

Radio1  present 8864 8000 0 80000000 80100000 4
POWER TABLE FILENAME = ram:/U5.bin

Radio2 not present 0 0 0 0 0 8
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-SAP2702I-E-K9 (PowerPC) processor (revision A0) with 376814K/134656K bytes of memory.
Processor board ID FCW1950NNBQ
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radios

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: XXXX
Part Number                          : 73-15XXXXXX
PCB Serial Number                    : FOC1XXXXX01
Top Assembly Serial Number           : FCWXXXXX
Top Revision Number                  : A0
Product/Model Number                 : AIR-CAP2702I-E-K9

 System is configured with default enable secret.Please change it before enabling HTTP Server



Press RETURN to get started!


*Mar  1 00:00:17.483: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar  1 00:00:23.631: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar  1 00:00:23.747: loading Power Tables from ram:/U2.bin. Class = E
*Mar  1 00:00:23.747:  record size of 3ss: 1168 read_ptr: 490F8EE

*Mar  1 00:00:28.943: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar  1 00:00:28.991: loading Power Tables from ram:/U5.bin. Class = E
*Mar  1 00:00:29.023:  record size of vht: 2904 read_ptr: 490F8EE

*Mar  1 00:00:29.083: Starting Ethernet promiscuous mode
*Mar  1 00:00:29.159: SCHED: Ethernet Bridge Process: install watched boolean System Initialized(48F7B30), os:1 ah:0
*Mar  1 00:00:31.267: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar  1 00:00:31.267: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar  1 00:00:31.767: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10
*Mar  1 00:00:31.771: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10
*Mar  1 00:00:31.771: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 27
*Mar  1 00:00:31.775: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 27
*Mar  1 00:00:31.787: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar  1 00:00:31.787: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Mar  1 00:00:31.799: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2700 Software (AP3G2-K9W7-M), Version 15.3(3)JPK, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2020 by Cisco Systems, Inc.
Compiled Tue 24-Nov-20 03:58 by prod_rel_team
*Mar  1 00:00:31.843: SCHED: Ethernet Bridge Process: remove watched boolean System Initialized(48F7B30)
*Mar  1 00:00:31.843: SCHED: Ethernet Bridge Process: install watched queue Soap BVI input queue(48EA238), os:0 ah:0
*Mar  1 00:00:31.843: No configuration in NVRAM..Auto Install initiated..
*Mar  1 00:00:32.267: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar  1 00:00:32.267: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
*Mar  1 00:00:32.783: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar  1 00:00:32.787: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar  1 00:00:32.787: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar  1 00:00:36.447: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (0-0)
*Mar  1 00:00:36.447: DPAA Initialization Complete
*Mar  1 00:00:36.447: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar  1 00:00:37.447: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar  1 00:00:39.859: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.178.207, mask 255.255.255.0, hostname ap

*Mar  1 00:00:46.279: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio0 due to the reason code 10
*Mar  1 00:00:46.279: %DOT11-5-EXPECTED_RADIO_RESET: Restarting Radio interface Dot11Radio1 due to the reason code 10
*Mar  1 00:00:46.279: %CDP_PD-4-POWER_OK: 15.4 W power - INJECTOR_CONFIGURED_ON_SOURCE inline power source
*Mar  1 00:00:48.279: %LINK-5-CHANGED: Interface GigabitEthernet1, changed state to administratively down

Greats

Dirk Meyer

[Scott Fella]

When you convert to autonomous, you have to go through the cli to do the initial configuration and to setup http(s) access.  Search the internet for "Cisco capwap to autonomous" and look at some blogs and docs to show the initial configuration.

Converting Cisco Wireless Access Point from Lightweight Mode to Autonomous Mode and Vice Versa – IT Network Consulting | Design, Deploy and Support | San Diego (speaknetworks.com)

Also search "cisco autonomous ap http access"

[Dirk Meyer]

Interface IP-Address OK? Method Status Protocol
BVI1 192.168.10.123 YES manual down down
Dot11Radio0 unassigned YES unset administratively down down
Dot11Radio1 unassigned YES unset administratively down down
GigabitEthernet0 unassigned YES TFTP up down
GigabitEthernet1 unassigned YES TFTP administratively down down

al ot of hours later i fund this out  the is no manual to get an http access to the ap.

mostly there are wrong or not compledet little therms.   i thouht it was easyer. my mistake

[Rich R]

Also beware of using the GUI on recent autonomous IOS.  If you search the forums you'll find lots of posts about some parts of the GUI which are broken.

End of SW Maintenance Releases Date was 29 April 2020 so Cisco no longer test these software releases so you can expect to find things broken which will never be fixed.

https://www.cisco.com/c/en/us/products/collateral/wireless/aironet-2700-series-access-point/eos-eol-notice-c51-740711.html

If you want to use the latest releases you may need to stick to using CLI not GUI.

If you want to use GUI you might need to use older releases which have security vulnerabilities (which are still being fixed up till 29 April 2022 in the later releases).

[Dirk Meyer]

version_suffix: k9w7-.152-4.JB6
version_directory: ap3g2-k9w7-mx.152-4.JB6
image_name: ap3g2-k9w7-mx.152-4.JB6
ios_image_file_size: 215552
total_image_file_size: 15135232
image_feature: WIRELESS LAN|LWAPP
image_family: AP3G2
system_type: 0x9b
ws_management_version: 7.6.100.0
info_end:

this is the odelst version  i found . it`s from 2014

version_suffix: k9w7-.153-3.JPK1
version_directory: ap3g2-k9w7-mx.153-3.JPK1
image_name: ap3g2-k9w7-mx.153-3.JPK1
ios_image_file_size: 10732032
total_image_file_size: 13998592
image_feature: WIRELESS LAN
image_family: AP3G2
system_type: 0x9b
ws_management_version: 17.5.1.12
info_end:

the newes,t date 03/21

wich version shoud i use?

the oldest and the newest i found dosen`t work

[Scott Fella]

Have you successfully converted the ap and are also able to ssh to the ip of the ap?  This will determine also if you have done the initial configuration properly or not.  Then the other docs that show you how to allow http and also configure the unit can be used.  Like what was mentioned also, the GUI can be problematic especially that its end of support.  Majority of folks configure these autonomous ap's from the CLI.  

Also the latest image I see on the downloads page is ap3g2-k9w7-tar.153-3.JPK1.tar which you have.

[Dirk Meyer]

i flashed  the newes versoin . and restart the ap. i have only the cli. i don`t get a ssh connection . i  can`t find out the current ip of the ap.

 i àm an absolut beginner.

yes the ap3g2-k9w7-tar.153-3.JPK1.tar is the latest image i have

[Scott Fella]

from the console, you should be able to login using Cisco/Cisco and also you should see what ip the ap receives from dhcp.  When you are consoled in.

[Rich R]

"show ip interface brief"

If your next question is how do I configure it?

You can find plenty of example configs for autonomous APs if you search.

You ideally need to be familiar with the basics of Cisco IOS and AP configuration to understand what you're doing.

[Dirk Meyer]

at first i was boered abaut your answers but  now i am happy. you give me usefull ttipps. but i hadto feind out what you mean with then.

 that`s the right way to learn something new. thank you very much.

https runs on all my ap`s. now i have to find how to configure then.

all ap`s has the aktuelly images.

[Scott Fella]

It is the right way to learn. It’s very hard to tell folks what they need to do when there are many different ways things fail. Even with new equipment, folks would research on the forums, reach out to Cisco folks or other engineers, search blogs and test.