07-23-2022 11:04 PM
I have searched everywhere for the default login to the CAP3501i and have found nothing.
Anyone able to provide this info?
07-23-2022 11:19 PM
Cisco/Cisco
07-23-2022 11:30 PM
So I hard reset the AP:
unplug
press mode button
plug in POE
hold mode button for 10 seconds (held 10 and then 180 seconds, to be safe)
I have tried
Cisco/Cisco
cisco/cisco
admin/admin
admin/password
07-24-2022 04:59 AM
- Post boot process after you tried the hard reset.
M.
07-25-2022 11:51 AM - edited 07-25-2022 11:55 AM
This is what happened when i booted up after holding down the mode button for 66 seconds.
it tries to access a file here, but not sure why 255
tftp://255.255.255.255/ap3g1-k9w7-tar.default
User Access Verification
Username: Cisco
Password:
% Authentication failed
Username:
Not in Bound state.
*Mar 2 12:18:20.399: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP ad dress is not assigned or assigned IP is wrong. Renewing DHCP IP.
r WRDTR,CLKTR: 0x8200083f 0x40000000
r RQDC ,RFDC : 0x80000033 0x00000217
using eeprom values
WRDTR,CLKTR: 0x8200083f 0x40000000
RQDC ,RFDC : 0x80000033 0x00000217
using MCNG ddr static values from serial eeprom
ddr init done
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
................................................................................ ................................................................................ ................................................................................ ......
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x8200083f, 0x40000000
RQDC, RFDC : 0x80000033, 0x00000217
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
Check PCIe signals to radio, re-seat radio.
PCIE1 port 1 not initialized
64bit PCIE devices
PCIEx: initialization done
flashfs[0]: 46 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31739904
flashfs[0]: Bytes used: 12608512
flashfs[0]: Bytes available: 19131392
flashfs[0]: flashfs fsck took 10 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 00:07:7d:f8:8b:60
Ethernet speed is 1000 Mb - FULL duplex
button is pressed, wait for button to be released...
button pressed for 66 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/ap3g1-k9w7 -tar.default
examining image...
%Error opening tftp://255.255.255.255/ap3g1-k9w7-tar.default (connection timed out)
07-25-2022 11:54 AM
it went to ap:
so I entered boot
ap: boot
Loading "flash:/ap3g1-k9w8-mx.153-3.JC14/ap3g1-k9w8-mx.153-3.JC14"...###############
File "flash:/ap3g1-k9w8-mx.153-3.JC14/ap3g1-k9w8-mx.153-3.JC14" uncompressed and installed, entry point: 0x4000
executing...
enet halted
IOS Secondary Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
......................................................................................................................................................................................................................................................
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x8200083f, 0x40000000
RQDC, RFDC : 0x80000033, 0x00000217
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
Check PCIe signals to radio, re-seat radio.
PCIE1 port 1 not initialized
Radio 1 : Vendor 0x11AB, Device 0x8324
64bit PCIE devices
PCIEx: initialization done
flashfs[0]: 45 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31739904
flashfs[0]: Bytes used: 12608512
flashfs[0]: Bytes available: 19131392
flashfs[0]: flashfs fsck took 10 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 00:07:7d:f8:8b:60
Creating Test Kernel diagnostic commands
Radio 0 : Vendor 0x11AB, Device 0x8324
Radio 1 : Vendor 0x6AF7, Device 0x5E5F
Radio 2 : Vendor 0x8673, Device 0x79F5
Radio 3 : Vendor 0x1086, Device 0x7840
******** AUTOMATIC DDR CALIBRATION UPGRADE LOGIC *********
=== 1. Is original FCS bootloader in BS:? If not, skip upgrade ===
---> original FCS bootloader not detected -- skip upgrade
Unable to locate IOS image with name **xx**.
Boot CMD: 'boot flash:/ap3g1-k9w8-mx.153-3.JC14/ap3g1-k9w8-xx.153-3.JC14'
Loading "flash:/ap3g1-k9w8-mx.153-3.JC14/ap3g1-k9w8-xx.153-3.JC14"...####################################
File "flash:/ap3g1-k9w8-mx.153-3.JC14/ap3g1-k9w8-xx.153-3.JC14" uncompressed and installed, entry point: 0x100000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 15.3(3)JC14, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Sun 29-Oct-17 16:49 by prod_rel_team
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
......................................................................................................................................................................................................................................................
flashfs[2]: 45 files, 9 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31481856
flashfs[2]: Bytes used: 12608512
flashfs[2]: Bytes available: 18873344
flashfs[2]: flashfs fsck took 10 seconds.
flashfs[2]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 0 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCC
Copy in progress...CCC
Copy in progress...CC
Uncompressing radio files...
...done Initializing flashfs.
Ethernet speed is 1000 Mb - FULL duplex
Radio0 present 8364B 8000 B8020000 0 B8030000 10
Rate table has 300 entries (16 legacy/64 11n/220 11ac)
POWER TABLE FILENAME = ram:/Z2.bin
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco AIR-CAP3501I-A-K9 (PowerPC460exr) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID FTX1531KC98
PowerPC460exr CPU at 666Mhz, revision number 0x18A8
Last reset from power-on
LWAPP image version 8.2.166.0
1 Gigabit Ethernet interface
1 802.11 Radio
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:07:7D:F8:8B:60
Part Number : 73-12175-05
PCB Serial Number : FOC15234CCG
Top Assembly Part Number : 800-32902-01
Top Assembly Serial Number : FTX1531KC98
Top Revision Number : A0
Product/Model Number : AIR-CAP3501I-A-K9
% Please define a domain-name first.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide