08-14-2012 02:37 AM - edited 07-03-2021 10:31 PM
Hello,
I have the problem that the AP1130 can not join to WLC2504.
Console Messages of AP1130:
*Aug 14 09:34:54.029: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 14 09:34:54.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.x.251 peer_port: 5246
*Aug 14 09:34:54.098: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_handshake.c:90 First fragment for seq 2 is missing
*Aug 14 09:34:54.098: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_handshake.c:90 First fragment for seq 2 is missing
*Aug 14 09:34:54.098: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_handshake.c:90 First fragment for seq 2 is missing
*Aug 14 09:34:55.414: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.x.251 peer_port: 5246
*Aug 14 09:34:55.415: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.x.251
., 1)14 09:35:14.199: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(UNKNOWN_MESSAGE_TYPE (5)
*Aug 14 09:35:14.199: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Aug 14 09:35:14.200: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.x.251:5246
*Aug 14 09:35:14.260: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
dir command of AP1130:
Directory of flash:/
3 -rwx 298 Aug 14 2012 09:35:56 +00:00 env_vars
158 drwx 128 Aug 13 2012 09:11:27 +00:00 c1130-rcvk9w8-mx
4 drwx 0 May 2 2011 13:58:48 +00:00 configs
5 -rwx 0 Mar 1 2002 03:08:31 +00:00 validate.txt
6 -rwx 7192 Aug 14 2012 09:36:14 +00:00 private-multiple-fs
36 drwx 320 Aug 14 2012 09:11:49 +00:00 c1130-k9w8-mx.124-25e.JA1
34 -rwx 5 Aug 13 2012 09:11:53 +00:00 private-config
The IP of the WLC is correct.
Solved! Go to Solution.
08-15-2012 02:27 AM
The system detects an invalid regulatory domain 802.11bg:-E 802.11a:-E for AP 00:3a:99:02:e8:10
Here is the problem.
Your country configured is Germany (which is in -E regulatory domain) while your AP is AIR-AP1131AG-A-K9 (which is in -A regulatory domain).
You either need to add a -A country to the WLC configuraiton (America for example) or replace the AP with part number AIR-AP1131AG-E-K9.
For which countries have which regulatory domains check this link:
HTH
Amjad
08-14-2012 03:41 AM
Hello,
What is your WLC version? you surely have correct configuration (ip, mask and default gateway) for both management and ap manager interfaces?
It seems you have some fragments lost. Can you describe your topology? how many ports are connected to the wireless controller?
Issue those debug command on WLC CLI while the AP is trying to join:
- debug mac addr
- debug capwap events enable
- debug capwap errors enable
For now it appears to be a cable or congestion issue. packets are getting lost and not all fragments reach the WLC/AP. You need to make sure that the cables used are good and the in-between devices are capable of taking the AP/WLC traffic.
HTH
Amjad
08-14-2012 03:48 AM
Hello,
WLC Version is 7.2.110.0
The Configuration is correct. I have two AIR-LAp1024 in the same Network and same WLC and the works correct.
Topology:
AP Vlan 10 Tagged <-> Switch with Vlan 10 <-> WLC Vlan 10 Tagged Port 1
The cable I will control the same...
08-14-2012 04:33 AM
see this in the console output:
., 1)14 09:35:14.199: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(UNKNOWN_MESSAGE_TYPE (5)
*Aug 14 09:35:14.199: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
The packets got dropped somewhere. Check your cables. This could probably be the issue. Try changing the AP port as well.
08-14-2012 04:46 AM
BTW, you need to collect the debug commands to see how things go from WLC perspective.
08-14-2012 04:34 AM
Can you please post the following command outputs:
1. WAP: sh inventory
2. WAP: sh version
3. WLC: sh sysinfo
08-14-2012 10:53 AM
Hi,
Things to check when an AP is not able to join the WLC:
1. Make sure that the CAPWAP ports or LWAPP ports are not being blocked between the WLC and the APs if they are remote to the WLC.
2. Check that the WLC has the correct time.
3. Check that the regulatroy domain of the AP is enable on the WLC.
4. make sure there is no latency issues between the WLC netowrk and the AP network.
As mention before get access to the console port of the AP and use the commands:
Issue those debug command on WLC CLI while the AP is trying to join:
- debug mac addr
- debug capwap events enable
- debug capwap errors enable
Also get the output of the:
1. WAP: sh inventory
2. WAP: sh version
3. WLC: sh sysinfo
08-15-2012 12:29 AM
I see in the log from the controller :
*spamApTask2: Aug 15 09:19:28.050: %CAPWAP-3-POST_DECODE_ERR: capwap_ac_sm.c:4700 Post decode processing failed for Config status from AP 00:3a:99:02:e8:10
*spamApTask2: Aug 15 09:19:28.049: %LWAPP-3-RD_ERR4: capwap_ac_sm.c:2523 The system detects an invalid regulatory domain 802.11bg:-E 802.11a:-E for AP 00:3a:99:02:e8:10
*spamApTask2: Aug 15 09:19:28.049: %LOG-3-Q_IND: spam_lrad.c:9884 The system detects an invalid country code () for AP 00:3a:99:02:e8:10[...It occurred 2 times.!]
*spamApTask2: Aug 15 09:19:28.049: %LWAPP-3-RD_ERR7: spam_lrad.c:9884 The system detects an invalid country code () for AP 00:3a:99:02:e8:10
*apfReceiveTask: Aug 15 09:19:27.889: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:289 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg
APf866.f2a3.40ae#sh inventory
NAME: "AP1130", DESCR: "Cisco Aironet 1130 Series (IEEE 802.11a/g) Access Point"
PID: AIR-AP1131AG-A-K9 , VID: V05, SN: FGL1441V3Q7
sh version:
ROM: Bootstrap program is C1130 boot loader
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)
APf866.f2a3.40ae uptime is 35 minutes
System returned to ROM by power-on
System restarted at 06:50:43 UTC Wed Aug 15 2012
System image file is "flash:/c1130-k9w8-mx.124-25e.JA1/c1130-k9w8-mx.124-25e.JA1"
cisco AIR-LAP1131AG-A-K9 (PowerPCElvis) processor (revision B0) with 27638K/5120K bytes of memory.
Processor board ID FGL1441V3Q7
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 7.2.110.0
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: F8:66:F2:A3:40:AE
Part Number : 73-8962-14
PCA Assembly Number : 800-24818-13
PCA Revision Number : A0
PCB Serial Number : FOC14390Z4L
Top Assembly Part Number : 800-29230-02
Top Assembly Serial Number : FGL1441V3Q7
Top Revision Number : A0
Product/Model Number : AIR-AP1131AG-A-K9
Configuration register is 0xF
sh sysinfo WLC:
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.2.110.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... Cisco_d8:1d:a4
System Location..................................
System Contact................................... xxxx
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.x.251
Last Reset....................................... Software reset
System Up Time................................... 1 days 18 hrs 16 mins 31 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin, Rome, Vienna
Configured Country............................... DE - Germany
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +25 C
External Temperature............................. +29 C
Fan Status....................................... 3800 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 3C:CE:73:D8:1D:A0
Maximum number of APs supported.................. 50
08-15-2012 02:27 AM
The system detects an invalid regulatory domain 802.11bg:-E 802.11a:-E for AP 00:3a:99:02:e8:10
Here is the problem.
Your country configured is Germany (which is in -E regulatory domain) while your AP is AIR-AP1131AG-A-K9 (which is in -A regulatory domain).
You either need to add a -A country to the WLC configuraiton (America for example) or replace the AP with part number AIR-AP1131AG-E-K9.
For which countries have which regulatory domains check this link:
HTH
Amjad
08-15-2012 03:10 AM
I agree with Amjad.
Your WLC is configured for Germany (regulatory domain of "E") and your WAP is for the Americas (regulatory domain "A").
This is the reason why the WAP refuses to join the WLC.
08-15-2012 03:20 AM
That was the problem. Now it works!
Thanks!
11-17-2015 06:54 AM
Hello,
The problem is known. I have now the same problem.
How have you changed the Access Point from US to Germany?
Thx.
best wishes,
Norbert
11-17-2015 09:10 AM
Hi Nobert,
It will be good if you create a new thread and put the complete information there.
*** You can change the regulatory domain of AP.
Grusse
Dont forget to rate helpful posts
11-18-2015 05:42 AM
Hello,
It is done ....
https://supportforums.cisco.com/discussion/12708341/air-ap1131ag-k9-can-i-change-domain-registry-ap-e
I thought, it is only a link and there is the same issue and so I added my thing here.
Sorry and THANKS.
best wishes,
Norbert
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide