07-30-2012 02:23 PM - edited 07-03-2021 10:28 PM
Hi,
I am all new to this. I have a stand alone 1140 AP and i am trying to perform a site survey using the AP; However I dont know what configs need to be on the AP for the survey ? can you help me please?
07-30-2012 02:33 PM
all you need is a very basic config. Just be sure to set the power to half what the client can support.
dot11 ssid Survey
authentication open
authentication key-management wpa version 2
wpa-psk ascii 0 Survey1234
!!
!
!
interface Dot11Radio0
no ip address
no ip route-cache
!
encryption mode ciphers aes-ccm
!
ssid Survey
HTH,
Steve
-----------------------------------------
Please remember to rate useful posts, and mark questions as answered
07-30-2012 02:49 PM
Thank you for your quick answer.
Both Radios need to be on? Radio0 and Radion1 which one is the 2.4 and 5 ghz?
07-30-2012 03:03 PM
It depends. If you are only looking for 2.4GHz, then no. But if you want 5GHz coverage as well, then yes.
Radio0 is the 2.4
Radio1 is the 5
HTH,
Steve
-----------------------------------------
Please remember to rate useful posts, and mark questions as answered
07-30-2012 03:09 PM
This What I have on the AP right now.
the ssid "Survey" needs to be brodcasted for the Survey? if so how can i set ip up on th eAP?
!
no aaa new-model
!
!
dot11 syslog
!
dot11 ssid Survey
authentication open
authentication key-management wpa version 2
!
!
!
username Cisco password 7 05280F1C2243
!
!
bridge irb
!
!
interface Dot11Radio0
no ip address
no ip route-cache
!
encryption mode ciphers aes-ccm
!
ssid Survey
!
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface Dot11Radio1
no ip address
no ip route-cache
!
encryption mode ciphers aes-ccm
!
ssid Survey
!
antenna gain 0
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
!
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
!
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
login local
!
end
07-30-2012 03:23 PM
under the SSID add the command guest-mode. that will broadcast the SSID. Don't forget to add in your wpa key as well
HTH,
Steve
-----------------------------------------
Please remember to rate useful posts, and mark questions as answered
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide